How much heat in joules must be added to 0.894 kg of beryllium to change it from a solid at 932°C to a liquid at 1285°C (its meltingpoint)?For beryllium: L₁ = 1.35×106 J/kg, Lv = 3.24×10 J/kg, c = 1820 J/kg C°Q =

Approach to solving the question:Please see attached photos for the detailed solutions. Thank you.…

Answered: How much heat in joules must be added…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A sample of hydrogen expands from 435 mL to 956 mL at constant temperature.Calculate the work done (in L-atm and Joules) if it expands against a constant pressureof 1.75 atm
Calculate the amount of barium from Sodium sulphate in a liter. A 100 ml solution of sodium sulphate (Na2SO4) is treated with solution of Barium chloride(BaC12). The precipitate, then ignited and weighed. the precipitate(BaSO4) weight is 0.1 gm. Mol.Wt of BaSO4 233.42 gm/mol, At. Wt of barium= 56 gm/mol. %3D
26) Given the T-T-T curve below, select the process that will result in a microstructure of nearly all bainite. C. Cool to 400°C, hold for 20 seconds, then quench to room temperature Cool to 500°C, hold for 10 seconds, then quench to room temperature Quench to 125°C, hold for 10 seconds, then reheat to 600°C for more than 100 seconds d. Cool to 725°C, hold for 1,000 seconds, then quench to 125°C Cool to 600°C, hold for 1 second, the quench to room temperature f. none of the above 900 Temperature (°C) 800 A+C 700 A+P 600 500 A+B 400 A 300 200 M(start) M(50%) 100 M(90%) TT 1600 1400 1200 1000 800 600 50% 0 1 10 102 103 104 105 106 Time(s) 400 200 Temperature (°F) 27) Fatigue failure situations are typically dependent upon which combination of the following factors? Slip plane, slip direction, and orientation of the applied load b. Yield strength, elastic modulus, and ductility of the material c. Temperature, time, and applied stress d. Stress amplitude, frequency of loading, and number…
A magnesium-lead alloy of mass 6.4 kg consists of a solid a phase that has a composition just slightly below the solubility limit at 300°C (570°F). The magnesium-lead phase diagram is shown in Animated Figure 9.20. (a) What mass of lead is in the alloy? i kg (b) If the alloy is heated to 400°C (750°F), how much more lead may be dissolved in the a phase without exceeding the solubility limit of this phase? kg
In 100 years, 100mg of radium decomposes to 96 mg. How many will be left after 580 years?
26) Given the T-T-T curve below, select the process that will result in a microstructure of nearly all bainite. a. Cool to 400°C, hold for 20 seconds, then quench to room temperature b. Cool to 500°C, hold for 10 seconds, then quench to room temperature c. Quench to 125°C, hold for 10 seconds, then reheat to 600°C for more than 100 seconds d. Cool to 725°C, hold for 1,000 seconds, then quench to 125°C e. Cool to 600°C, hold for 1 second, the quench to room temperature Temperature (°C) f. none of the above 900 800 H A+C 1600 1400 700- 1200 A+P 600 P 1000 500H A+B 800 400- Temperature (°F) 4 A 300- M(start) 200 M(50%) 100- M(90%) 600 50% T 0 1 10 102 103 10 105 106 Time (s) 400 200 27) Fatigue failure situations are typically dependent upon which combination of the following factors? a. Slip plane, slip direction, and orientation of the applied load b. Yield strength, elastic modulus, and ductility of the material c. Temperature, time, and applied stress d. Stress amplitude, frequency of…
:Ratio of Oxygen and Iron in the crust is about 40% O 50% O 60% O :It is study of rock layers and their formation Seismology O Stratigraphy O Paleontology O :Basalt is considered basic volcanic rock O basic plutonic rock O acidic volcanic rock O
Considering an alloy of the two soluble components A and B described by a phase diagram Figure P2.31, determine the masses of the alloy that are in the liquid and solid phases at a given temperature if the total mass of the alloy is 100 g, component B represents 40% of the alloy, 20% of the liquid is component B, and 50% of solid is component B.
41)
An aluminum-alloy rod has a length of 8.1814 cm at 14.00°C and a length of 8.1942 cm at the boiling point of water. (a) What is the length of the rod at the freezing point of water? (b) What is the temperature if the length of the rod is 8.1916 cm? prob (a) Number i Units (b) Number i Units

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

How much heat in joules must be added to 0.894 kg of beryllium to change it from a solid at 932°C to a liquid at 1285°C (its melting point)? For beryllium: L₁ = 1.35×106 J/kg, Lv = 3.24×10 J/kg, c = 1820 J/kg C° Q =