How many kN of lead (SG=11) must be fastened outside the bottom of a 1-m diameter cylinder to make it float vertically with 1.5 m above the water? Weight of cylinder = 3562 N, Height of the cylinder = 4 m 17.270 kN 25.679 kN 23.405 kN 19.262 kN

Q: B 3.1 m 4.0 m 4.0 m 4.0 m 4.0 m 25 kN 65 kN 25 kN

A:

Q: 1) II) Find the depth D, in which the wood will be submerged. Is the wood cylinder stable? Show your…

A:

Q: A wooden cylinder (sg=0.61) is placed vertically in oil with specifc gravity of 0.85. Determine the…

A: The metacentric height (MB) =?

Q: C. Three cylinders are piled in a rectangular ditch as shown. R, = 5cm, R2 = 6 cm, R3 = 5 cm. W, =…

A: Reactions at A, B and C are :

Q: B6

A:

Q: Complete the table with solution please)

A:

Q: 5.0 m 5.50 m 6.0 m 7.0 m 5.0 m (1b0+SN) KN 144 KN E G 120 KN _96 kN M IN 5.0 m 4.50 m 4.20 m 4.0 m

A:

Q: A solid cylindrical buoy is made up of pine (Sg = 0.5) and lead (Sg = 11.3) weights attached as…

A: Given data in question  Specific gravity  Depth Diameter

Q: A beam-spring system is shown L = 5m EI-2.5 × 10³ kN-m² figure below. heee 000 k = 40 kN m-10 kN k=…

A: For given spring-beam system,Initial displacement of 5 mmInitial velocity: 135 mm/sto find the…

Q: 4. A cylinder 8l 4.5 nas a height of 2.5 metres. Find the meta-centric height of the cylinder when…

A: option a is correct

Q: FIGURE 02 6 KN 5-25. 2.50 KN B. 2m 2M FIGURE O3

A:

Q: A closed rectangular tank measuring 5 m long, 1.59 m wide, and 2 m high is filled to a depth of 1.6…

A: Given data,  L = 5m B = 1.59 m h = 1.6 m H = 2 m Horizontal acceleration = 9.81 m/s² SG = 0.68   To…

Q: Piston A has a cross-section of 1200 cm^2 while that of B is 800 cm^2. B is higher than A by 2m. If…

A: Force: The movement or change in the motion of the component due to applied external action on a…

Q: 1. Portal Method The frame shown is subjected to lateral loads as shown. Supports S, T, U V, W and X…

A:

Q: 1. Portal Method The frame shown is subjected to lateral loads as shown. Supports S, T, U V, W and X…

A: To Find the Forces in the frame member

Q: A sphere 850mm-diameter floats half submerged in a tank of oil (sg=0.90) 4. What is the total…

A:

Q: Wu L1 L2

A: The moment distribution method is a structural analysis method for statically indeterminate beams…

Q: A rectangular watertight box is 600 mm long, 400 mm wide and 200 mm deep. It weighs 220N. If it…

A: Given, Length = 600 mm or 0.6 m  Width = 400 mm or 0.4 m  Depth = 200 mm or 0.2 m  Weight (W) = 220…

Q: A hollow (open) hemispherical cup and a closed cylindrical buoy is floating in water as shown. The…

A: Draw the free body diagrams of both cup and cylinder. Note that since the hemisphere is hollow and…

Q: Compute the value of R1 and R2.

A:

Q: be with a side of 550 mm. What force letely submerged the cube in water if its sp c. 344. d. 245. a.…

A:

Q: 3. A vertical circular gate in a tunnel 8 m in diameter has oil on the other side and air on the…

A: Given:The diameter of the gate is 8 m.The specific gravity of oil is 0.8.The depth of oil is 12…

Q: The areas of the pistons in a hydraulic machine are 5cm² and 625cm². What force on the smaller…

A: Areas of pistons- A1=5 cm2 A2=625 cm2 Load F1=1250 N, It is needed to find the Load F2.

Q: Problem 2 (d): An aluminium bar with a cross-sectional area of 850 mm² is loaded as shown. EA = 70x…

A:

Q: 2. Cantilever Method: The frame shown is subjected to lateral loads as shown. Supports S, T, U V, W…

A:

Q: Piston A has a cross-section of 1,200 cm^2 while that of B is 800 cm^2. B is higher than A by 2 m.…

A:

Q: 20 kN 10 kN 4 m 2 m 4 m

A:

Q: Consider the cross-section of the gravity concrete dam shown below. Check its stability against…

A: Above given data of dam we have to check its stability against overturning

Q: Q.₁ Compute the maximum capillary tension for a tube of 0.12 mm in diameter at 4°C A 1.26 kN/m² B…

A: Diameter- d=0.12 mm,

Q: Determine the following reactions. P = 185 kN; Q = 120 kN; and R = 40 kN (*note that you are to…

A: Given data Q=120kNR=40kN/m

Q: Q/ Find P,-Pe and Also find h in the figure below if Pa-Pa is 11.5 KN/m. Water h=? Oil R.D= 0.8…

A:

Q: A vertical cylindrical tank 1 m in diameter and 3 m tall weighs 3.86 kN. Which of the following most…

A: Given data- A vertical cylinder tank- Diameter d=1 m,Height h=3 m,Weight W=3.86 kN,Unit weight of…

Q: Determine roller support reaction

A: Given data : The value of Point load P=5 KN The value of Point load Q=8 KN The value of Point load…

State Plane Coordinate Systems

The state plane coordinate system (SPCS or SPS) is a collection of 124 coordinate systems or geographic zones prepared for particular regions of the U.S. Every state consists of one or more than one state plane zone, the boundaries of which generally follow the county lines. Inside the U.S., there are 110 zones in total, 10 more zones in Alaska, 5 in Hawaii, and 1 for Puerto Rico and US Virgin islands. The system is extensively used for geospatial and geographic data assembling by the state and local governments.