Determine the following reactions. P = 185 kN; Q = 120 kN; and R = 40 kN (*note that you are to insert the answer without any unit and do not include an R 12º Reaction Dy = Ey = 6. Ex = C Magnitude

Q: 5.1 The recommended scales for use on technical drawings are specified in the following table.…

A: To find: Choose the suitable code for the given scales for use on technical drawings.

Q: Compare and contrast the uses of T-square and setsquares.

A: T-square: It is a technical instrument that is used for drawing purposes.  It is mainly used by…

Q: Which of the following is the largest scale? O 1cm:1mile O 1 mm:10m O. 1:1000 1cm:1km

A: to check largest or smallest scale firstly convert all numerator and denominator in same unit of all…

Q: Determine the Centroid of 3 Areas.

A:

Q: answer in 4 decimal places

A:

Q: Write the IUPAC name for   compound.

A: International Union of Pure and Applied Chemistry (IUPAC)) is the naming pattern or nomenclature…

Q: The value of the smallest division on the main scale of a horizontal circle is graduated to 1/6 of a…

A:

Q: FIHD THe CENTROID (x $ Y) of THe GazOMETRY

A: Centroid is the point where the mass of whole body acts. If there is a figure which consists of…

Q: derivation of the formulas used in every section

A: This question has been taken from fluid mechanics

Q: what letter are those?

A: According to me  This symbol represent bending moment at any distance ( x ) in a beam.

Q: X 0.75 3 -3.5 1.5 1.5

A:

Q: Please find the centroid x and y bar, and Ixx for the following shapes. Show all work with neat…

A: Approach to solving the question:Breaking the composite shape in simple shapes and using Centroid…

Q: ETERMINE THE LOCATION OF CENTROIDAL X AND Y. NOTE: UNITS ARE IN INCHES.

A:

Q: Please find the centroid x and y bar, and Ixx for the following shapes. Show all work with neat…

A: :

Q: Q1:A)Write the command to draw Figure below by using Auto CAD program (Relative Coordinate Method).…

A: question being asked here is to draw the above diagram using AUTO CAD program and also clearly…

Q: Explain the Modified Mercalli scale.

A: The effect caused on the surface of the earth due to an earthquake is known as the intensity of the…

Q: * To draw an arc angle between two intersecting lines Fillet O Block O Trim Chamfer O If we want to…

A:

Q: a) top most, hef tmost

A: X = 1.5 cm Y = 5.48 cm

Q: Write the types of structures in detail.

A: The type of structure to be constructed for a purpose depends upon the use of structure, load on…

Q: Use the CAD drawing below and determine distances A and B to the nearest hundredth inch. + 2 A = O O…

A:

Q: What size will it be if 4" is at scale 2"=1"

A: Given tha scale  2"=1" Thus defines the sclae ratio  for a drawing is 2:1. Scale ratio = drawing…

Q: Problem 12.16 Consider the building frame shown in (Eure) Suppose that My 2.6 k/ft and s8 k/ft.…

A:

Q: Classify the structure shown in the figure. OA. Indeterminate. 21st degree O B. Indeterminate, 24th…

A:

Q: The plan of an area drawn with the original scale of 1 cm = 10 m, has shrunk such that a line,…

A: Given data- Original scale 1 cm = 10 m, 15 cm long line measures 14.5 cm, To Find- The shrunk scale…

Q: Define Relative precision.

A: Relative precision:

Q: Find All dimensions are in inches. Round answer to the nearest second 2.250 2.601 4.059

A:

Q: Please find the centroid x and y bar, and Ixx for the following shapes. Show all work with neat…

A: Approach to solving the question: Detailed explanation:Examples: Key references:

Q: Define Class 1 and 2 of cross sections

A: Class 1 cross-sections are those which can form a plastic hinge with the rotation capacity required…

Q: Below in Figure is an isometric drawing of a component. Draw in First Angle Projection the…

A: Question being asked here to draw the first angle projection in which the drawing pattern is…

Q: Find the centroid of X and Y in tabular form.

A: A centroid is a point on the body on which the mass of a body is uniformly distributed. If the body…

Q: 12 13 12 13 14 10 Which tools that can be used to :4 draw the following shape in .AutoCAD R5 R10 R12…

A: To draw the given shape we will require the following command necessarily :- Dimension, line or…

Q: Define Torsion,

A: Torsion: The twisting of a material by the loading of external forces i.e couple which produces…

Q: 2"

A:

Q: subtract the numbers.796 -81

A: The given numbers are  796,-81

Braced cuts

The braced cut is a method of providing lateral support to the soil in foundation trenches, to prevent the trenches from deformation by the caving in of soil and resisting it from moving laterally. During shallow excavation in firm soil, generally, slopes are provided to resist the caving in of soil. During shallow excavation in soft soil and deep excavation, the chances of caving in of soil increase. Hence, it becomes necessary to make a provision to resist the deformation of trenches due to caving in of soil. The braced cut is the method used for such conditions. The excavation using braced cuts is a bit uneconomical as compared to the traditional open-cut excavation method but provides better safety than the cut excavation method.