Heat exchangerWoycleTurbineCompressorHeat exchangerDetermine:(a) the mass flow rate of air, in kg/s.(b) the rate of heat transfer, in kW, to the working fluid passing through the heat exchanger.(c) the percent thermal efficiency. An ideal air-standard Brayton cycle operating at steady state produces 10 MVWof power. Operating data at principal states in the cycleare given in the table below. The states are numbered as in the figure below.State p(kPa) T (K)h (kJ/kg)11003003001000574.1579.73100018002002410010341085

Answered: Image /qna-images/answer/ca077bd4-5bf4-4cba-b5b9-8697ba7dcb49.jpg

Heat exchanger Veycle Compressor Turbine Heat exchanger Determine: (a) the mass flow rate of air, in kg/s. (b) the rate of heat transfer, in kW, to the working fluid passing through the heat exchanger. (c) the percent thermal efficiency.

Heat exchanger Veycle Compressor Turbine Heat exchanger Determine: (a) the mass flow rate of air, in kg/s. (b) the rate of heat transfer, in kW, to the working fluid passing through the heat exchanger. (c) the percent thermal efficiency.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please help me???
* İl. Gmail ► Untitled docu.. A system consists of a turbine and heat exchanger are connected in series. The working fluid is entering the turbine at P1 0.6 Mpa, T= 200 °C and leaving it with P,= 0.2Mpa. Then the turbine exit becomes the heat exchanger inlet to increase the fluid temperature to become 800 °C. Considering that the adiabatic power y =1.4 and the specific heat = 1.005 KJ/Kg.K. Determine the turbine production work WT and heat exchanger energy needed to be added quE. T = 200 °C P,= 0.6 Mpa- T T2 ? P,=0.2 Mpa h high НЕ T= 800 °C P3 =? 9 in
In a heat exchanger, the heat transfer depends on the choice of the control volume
Concentric Tube Heat Exchanger For equivalent inlet conditions, why should a counterflow heat exchanger have better effectiveness than a parallel unit?
Please show complete solutions and detailed drawings. Show conversions, units, and box in the final answers
7) Outlet Temperature and Heat-Transfer Rate via Minimum Allowable Approach Temperature. Hot oil at a flow rate of 3.00 kg/s (Cp = 1.92 kJ/(kg-K)) enters an existing 1-1 counterflow exchanger at 400 K and is cooled by water entering at 325 K (under pressure) and flowing at a rate of 0.70 kg/s. The overall U = 350 W/(m².K) and A= 12.9 m². Calculate the heat-transfer rate and the exit oil temperature if the minimum allowable approach temperature is to be 10 °C (10 K).
It is based on the centralised production of chilled water and its distribution for a wide range of indoor air cooling purposes. Consumer Substation Thermal Energy Storage Tanks Hot Plate heat exchanger District Cooling
Superheated steam from the boiler expands in the turbine from inlet pressure p₁ of 50 bar and temperature 7 of 487 °C to condenser pressure p2 of 18 kPa. In the condenser, the steam condenses to saturated water. The isentropic efficiency of the turbine ns is 78.0 %. The mass flow of steam 9m,h is 140 kg/s. In the boiler, heat flow rate to the circulating fluid (water/steam) is 458 MW. Read from h,s-diagram and calculate: 1. Enthalpy of the superheated steam h kJ/kg (with zero decimal accuracy) 2. Enthalpy of the steam at turbine outlet after isentropic expansion h₂s kJ/kg (with zero decimal accuracy) 3. Enthalpy of the steam at turbine outlet h₂ kJ/kg (with zero decimal accuracy) 4. Turbine power Pt MW (with one decimal accuracy) 5. Steam content at the turbine outlet X2 kJ/kg (with two decimal accuracy) 6. Enthalpy after condenser h3 kJ/kg (with zero decimal accuracy) 7. Thermal power of condenser Qc 8. Thermal efficiency of the plant n MW (with one decimal accuracy) % (with one…
Q.2. Air enters a steady-flow heat exchanger with a mass flow rate of 2 kg/s as shown in Figure. Determine (a) the rate of heat transfer to the air in the heat exchanger, (b) the power output from the turbine assuming no heat loss, and (c) the velocity at exit from the nozzle. (Cp atr = 1.005 kJ/kg. K) T=600 C T- 12 C V=3 m/s Air Нeat v-3 m/s Exchanger Turbine T= 200 C V - 25 m/s T= 160 C Nozzle
Refrigerant 22 is the working fluid in a Carnot refrigeration cycle operating at steady state. The refrigerant enters the condenser as saturated vapor at 36°C and exits as saturated liquid. The evaporator operates at -30°C. Determine, in kJ per kg of refrigerant flowing, the net work in the cycle. A 20.37 B 36.47 18.37 24.37