Answered: hA he J L2, D2 L1, D1 hc D1 = 200 mm D2…

Engineering

Mechanical Engineering

hA he J L2, D2 L1, D1 hc D1 = 200 mm D2 = 250 mm D3 = 400 mm L3, D3 %3D %3D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Blood flows from the left ventricle (LV) of the heart, which has an exit diameter of d; = 16 mm, through the stenotic aortic valve of diameter dz = 8 mm, and then into the aorta A having a diameter of d3 = 20 mm. If the cardiac output is 4 liters per minute, the heart rate is 90 beats per minute, and each ejection of blood lasts 0.31 s, determine the pressure change over the valve. Take p = 1060 kg/m. LV di ds A
A pipeline of 50 mm diameter and 4.5 km length connects two reservoirs whose constant difference of water level is 12 m. A branch pipe 1.25 km long and taken from a point distance of 1.5 km from reservoir A, leads to reservoir C whose water level is 15 m below that of reservoir A. Find the diameter of the branch pipe so that the flow into both the reservoirs is the same. Assume the coefficient of friction for each pipe, f = 0.0075, and neglect minor losses.
An elbow deflects water upward and discharges it to the atmosphere at a specific rate. Determine the gage pressure at the inlet of the elbow and the anchoring force needed to hold the elbow in place. (gage pressure at the outlet is zero)
A storm drain has a maximum capacity of 120 L/min. During heavy rains, an influx of 240 L/min approaches the drain. Assuming the drain is cylindrical, by how much would the drain radius need to be increased to handle the heavier rainfall? Assume the water travels at the same linear speed in both drains. The answer is 1.4. Please explain why A 16 times greater B 42 times greater C 2 times greater D 1.4 times greater
Water is pumped from the upper reservoir to the lower reservoir through the piping system shown. Determine the power required for the pump if the water flow rate is 60 kg/s. The fittings from pipe Di to pipe D2 and from pipe D2 to pipe D3 can be considered to be standard 90° elbows with velocity in pipe 2 for the friction loss. Data: h = 10 m, h2 = 3 m, L1 water viscosity = 1 cP = 103 kg/m-s, p= 1000 kg/m³. The pipe roughness is 0.05 mm. The pump efficiency is 75%. 50 m, L2 = 300 m, L3 = 2 m, D¡ = 0.2 m, D2= 0.5 m, D3 = 0.03 m, (1) D,, L, D2, L, Globe valve D3, L,
4. Two reservoirs, A and B, are connected by a pipeline which is 1300 m long. The surface of reservoir B is 10 m lower than that of reservoir A. There is a small hill between the two reservoirs with the highest point at 500 m along the pipe from A. If the pipeline has a diameter of 300 mm and a friction factor of λ = 0.008 then determine the following: (Ignore the minor losses and assume that the pipe is already flowing full and at a steady flow) (a) The flow in the pipe (b) If the lowest permissible absolute pressure head in the pipeline is 2.5 m of water, determine how high above reservoir A surface level the pipe can be laid so that the minimum pressure condition is satisfied. (Assume atmospheric pressure of 105 Pa.)
A high-pressure washing system's pump supplies 1 gallon of water persecond at 100 psi pressure. The nozzle should be designed so that the static pressureof the water as it exits the nozzle is the same as the atmospheric pressure. If theinside diameter of the hose leading from the pump to the nozzle is 2 in., whatshould the diameter of the nozzle exit be? What will be the velocity of the waterat the exit of the nozzle?
The discharge of water in the given pump is given as 0.030 cubic meters per seconds. Use ywater = 9.79 KN/m° and Pinput = 27.34 hp. Determine the following parameters, if losses and elevation changes is to be neglected. 0.409 MPa 0.125 MPa a. The energy added in meters and the power delivered in kilowatts to the water by the pump. b. The mechanical efficiency of the pump. P 0.04meter Ø 0.1meter Ø
Water flows into the pipe connection shown at '6' and '2' and leaves the system at '1'. It is not open to the atmosphere at any connection. The gauge pressure at both inlets is 12 psig and the velocity at both inlets is 9.5 ft/sec. Determine the horizontal force (lbf) needed to hold the fittings in place. 2 7.5" 1 2.5" 3 4 5 6 1.0"
+7