H.W.2: A gat (AB) is supportedby pin (A) of diameter (16mm)cableBwith double shear and cableat (B) of diameter (20mm).Find the maximum allowableload (w kN/m) so that the 8.0mtensile stress of the cable andw=7(kN/m)shear stress of the bolts at (A)will not exceed (150mPa) andA(100MPA), respectively.

Answered: Image /qna-images/answer/23c4803e-5c32-4143-a7d4-8eaf9c721dd2.jpg

H.W.2: A gat (AB) is supported by pin (A) of diameter (16mm) cable with double shear and cable at (B) of diameter (20mm). Find the maximum allowable load (w kN/m) so that the 8.0m w=7(kN/m) tensile stress of the cable and shear stress of the bolts at (A) will not exceed (150mPa) and A (100MPA), respectively.

H.W.2: A gat (AB) is supported by pin (A) of diameter (16mm) cable with double shear and cable at (B) of diameter (20mm). Find the maximum allowable load (w kN/m) so that the 8.0m w=7(kN/m) tensile stress of the cable and shear stress of the bolts at (A) will not exceed (150mPa) and A (100MPA), respectively.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

a) The floor system shown is subjected to a total uniform distributed load of 12 KN/m². Sketch the loading that acts along the members DE and BDG. -2.0 m - 3.0 m- A 3.0 m D E 5.0 m F G
B8
For a draped cable, where the two kinks are located at a distance L/3 from each two end of a prestressed beam, which of the following(s) is/are correct? (L refers to the total length of the beam, and the eccentricity is zero at anchorage ends and e at mid-span) (1) The equivalent load is an uniformly distributed load, wp=-8Ph/L² (2) The equivalent load is a point loads 3Pe/L at the two kinks (3) The bending moment at the mid span from prestress is Pe (2) (2), (3) O (1) ○ (1), (2)
A cable supports two vertical loads as shown in Fig. If the maximum tension in the cable is 1000 Ib, de- termine The vertical distances ys and yc. 15 ft 15 ft 15 ft A 7.5 ft D IC 500 lb 200 lb
show clean solution and fbd pls
I need datiled solution with clear calculations
Rigid bar ABC is supported by member (1) at B and by a pin connection at C. Member (1) has a cross sectional area of 1.35 in.² and a yield strength of 45 ksi. The pins at B, C, and D each have a diameter of 0.7 in. and an ultimate shear strength of 78 ksi. Each pin connection is a double-shear connection. Specifications call for a minimum factor of safety in member (1) of 1.5 with respect to its yield strength. The minimum factor of safety required for pins B, C, and D is 2.9 with respect to the pin ultimate shear strength. Determine the allowable load P that may be applied to the rigid bar at A. Use overall dimensions of a = 46 in. and b = 94 in. D (1) b A kips P Answer: Pallow= i a B
Show the complete solution.
The 4mm-diameter cable Bc is made of steel with E-200Gpa knowing that the stress in the cable must not exceed 200Mpa and that the elongation of the cable must not exceed 6m find the maximum load P that can be applied as shown B 2.5 m 3.5 m 4.0 m
Design a clamp coupling to transmit 25 kW at 120 r.p.m. The allowable shear stress for the shaft and key is 50 MPa and the number of bolts connecting the two halves are six. The permissible tensile stress for the bolts is 75 MPa. The coefficient of friction between the muff and the shaft surface may be taken as 0.3.
Solve correctly please