If the aluminum cable is removed and no lon ger supporting Bar ABC. A concentrated loa d is then applied at Point B and another con centrated load at Point C. Both loads have magnitude of 30 KN. Determine the minimu m safe diameter of the pint at Point B if the a llowable shear of the pin is 50 MPa. Assume that the pin at B is double shear.

If the aluminum cable is removed and no lon ger supporting Bar ABC. A concentrated loa d is then applied at Point B and another con centrated load at Point C. Both loads have magnitude of 30 KN. Determine the minimu m safe diameter of the pint at Point B if the a llowable shear of the pin is 50 MPa. Assume that the pin at B is double shear.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

8 in. B 6 in. 1.5 C 4 in.- D P PROBLEM 1.51 Link AC is made of a steel with a 65-ksi ultimate normal stress and has a ½ × ½-in. uniform rectangular cross section. It is connected to a support at A and to member BCD at C by-in.-diameter pins, while member BCD is connected to its support at B by a -in.-diameter pin. All of the pins are made of a steel with a 25-ksi ultimate shearing stress and are in single shear. Knowing that a factor of safety of 3.25 is desired, determine the largest load P that can be applied at D. Note that link AC is not reinforced around the pin holes.
Simply Supported Beam ABCDE below carries multiple loads as shown. A built-upsection made from a T-Section and a Channel (C-Section) fastened together by 16mm∅ bolts,equally spaced from the center of the section, with shearing capacity τ=100 MPa, for bearing σb= 220 MPa for rivets in single shear and σb = 280 MPa for rivets in double shear. E=200GPa forall materials. Determine the moment capacity of the section, kN-m, if fbcap≤300 MPa.
Assume a concrete cover or 40mm, 10mm stirrups and clear distance between layers of 25mm. For Problem 9 and 10, determine the concrete and steel stresses at the fixed Support C 1.6P (6 Section at C Wo 28 kN/m W- 11 kN/m Pa 112 kN Pu = 52 kN 3.3m 1.5m 3.9m 8-36mmo 4.6m f- 25 MPa Grade 40 rebars d' 75mm A d 585 mm 4-36mm b-300mm
Simply Supported Beam ABCDE below carries multiple loads as shown. A built-upsection made from a T-Section and a Channel (C-Section) fastened together by 16mm∅ bolts,equally spaced from the center of the section, with shearing capacity τ=100 MPa, for bearing σb= 220 MPa for rivets in single shear and σb = 280 MPa for rivets in double shear. E=200GPa forall materials. Determine the moment of inertia of the section in x10^6 mm^4
The five-bolt connection must support an applied load of P = 2600 lb. If the average shear stress in the bolts must be limited to 27 ksi, determine the minimum bolt diameter that may be used for this connection. Cocoo Answer:dmin- P in.
it Q4/A/Determine the Maximum axial stress for a 36-ft joint of 7.625-in.OD.6.625in.1D, 39 Ib/ft. N-80 casing with API long, round thread couplings if the casing subjected to a 400 000 lbf axial tension in a portion of directional wellbore having a doglog severity of 4"/100ft.Compute the maximum axiat stress assuming: 1-Uniform contact between the casing and the borehole wall. 2- Contact between the casing and the borehole wall only at the couplings. 3-The joint strength of the API round thread-couplings. Take (oult for N-80-100 000 lbf). utmat
Answer with complete fbd,
69 H.W A shnft comBsed of Seymeats Ac, cD and DB is fastened to igid SurPorts ond looded as shown, for steel G=83 GN/m?, for Aluminum G=28GNIm? and for bronze G= 35 GN/m Determine the maximum shearing Stress oleve lored in each Segment? Ans: T=472N.m, Tal=9.3MN3 To=700d Te-300N.m Steel Aluminum Bron 2e d=25mm d= Somm d=25mm 2m 1.5m
A four story "intermediate reinforced concrete moment frames" supports seismic weights of 1400 kip on each floor and 500 kip on the roof. The natural (fundamental) period of this frame as T-0.6 sec. Based on ASCE 7-16 procedures, the base shear this frame must resist in an earthquake is V-846 kip 14 ft 14 ft 14 ft 14 ft A A 7777 7777 777 w=500 kip w=1400 kip w=1400 kip w=1400 kip 7777 1. Based on the natural period, linearly interpolate the value of k that should be used for the equivalent lateral force method. 2. Using your interpolated value of k and the base shear, compute the vertical distribution of lateral loads. 3. Draw an elevation of the frame showing the lateral loads applied to each floor and the roof. 4. Assuming k-2, compute the vertical distribution of lateral loads. 5. Draw an elevation of the frame showing the lateral loads applied to each floor and the roof when k=2.
Design a clamp coupling to transmit 25 kW at 120 r.p.m. The allowable shear stress for the shaft and key is 50 MPa and the number of bolts connecting the two halves are six. The permissible tensile stress for the bolts is 75 MPa. The coefficient of friction between the muff and the shaft surface may be taken as 0.3.
A16mm–diameter steel rod AB is fitted to a round hole near end Cof the wooden member CD. For the loading shown, determine, (a) the distance bfor which the average shearing stress is 7Mpa a on the surfaces indicated by the dashed lines, (provide FBD and answer in mm)(b)the average bearing stress on the wood (provide FBD and answer in Mpa)
(Design Of Steel Structures) 4. Beam ISLB 500 at 750N/m carries total factored uniformly distributed load of 300kN. It is supported on columns ISHB300 at 630N/m at each end. The connection is made is using M20 bolts of grade 4.6 and steel Fe410. Design the connection.