A damper square mat is supporting a dead load weight of 8 kN. Helical springs will be used to support the load located at all corners with shearing stress of 120.6 Mpa at 20 turns. The spring has a deformation of 98.7 mm with a mean radius of 80 mm. Design the minimum diameter of the wire to support a load. Use G = 83 Gpa.

A damper square mat is supporting a dead load weight of 8 kN. Helical springs will be used to support the load located at all corners with shearing stress of 120.6 Mpa at 20 turns. The spring has a deformation of 98.7 mm with a mean radius of 80 mm. Design the minimum diameter of the wire to support a load. Use G = 83 Gpa.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Help me answer & find the solutions pls.
Design the shear reinforcement for the beam shown in figure below assuming it resists an ultimate shear force at distance d from the face of the support of 450 kN. The characteristic material strengths are fok= 25 N/mm²and fm = 500 N/mm² 450 kN d= 500 mm -4H25 b= 300 mm
At which point on the design P-M interaction diagram is the design flexural strength largest? O Pure compression Pure tension Balanced failure point (CCL limit) O TCL limit Beam condition (Pn = 0) %3D //img00.zhaopin.cm
complete and clear solution
a) Two bars of different size form a pin-connected frame that supports a Load 'P' at point A as shown in the Fig. 3. What safe load P (kN) can be applied if the allowable stress of 120 MPa is not to be exceeded? Assume buckling has been prevented. Allowable stress is based on a factor of safety of 2.0. Cross sectional area of the rods AB and AC are given in the adjacent table as per last digit of Roll number. What is the failure load? Last digit of Area of AB | Area of AC Roll No. 1, 2, 4 & 7 200 mm 230 mm“ 3, 6 & 8 160 mm- 190 mm² 5, 9 & 0 180 mm 210 mm 2400 1600 Fig. 3 b) Two square bars are of equal length but have different size as shown in Fig. 4. Compare the maximum stress in the two bars if they are to receive the same input of energy from axial load. Given, m = (2 + last digit of your roll number). 2a 5.x m.x Fig. 4 last digit of roll=1
Answer in two decimal places please
Provide solution and mention all steps
Given the truss and loading shown below, determine the stress at member DF if Pµ = 18.375 Kips and its area is 16 in². Assume that the truss are simply supported at joint M and E. Express your answer in ksi. Use three decimal places. RM Pu Pu 0 Pu Pu 8 @ 10' = 80' Pu B Pu CF Pu et LK J I H G F 8@10' 80' RE
Need answer ASAP complete solution please
CHOICES STABILITY 8 2 0 3 7 10 1 9 4 Statistically Determinate 5 6 Unstable Stable None Statically Indeterminate
Rigid beam AB is supported by three bolts at A and a pin at B. The bolts at A are in double shear and have a diameter of 0.250 in. Assume L= 4.0 ft. If the average shear stress in the bolts cannot exceed 70 ksi, determine the maximum distributed load wmax that can be supported by the structure. (1) A Answer: Wmax IN L B kips/ft