Answered: h = 1.4 H = 1.1 m…

h = 1.4 H = 1.1 m K = 4.87 x 10-2 cm/sec θ = 14° L = 36 m a.)Find the hydraulic gradient. b.)Compute the cross-sectional area of the figure in m2. c.)Solve the rate of flow in m3/hr.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A 300 mm pipe delivers 2 cu.m. of water per minute through a venture meter shown. A2 is 1/10 of A1.…

A: Applying Bernoulli theorem and continuity equation to solve problem

Q: Water flows steadily through a smooth circular tube of 10 cm diameter at a flow rate of 2 kg/s. The…

Q: Q2 12 m Concrete dam Water 1.5 m water 5 m Impervious clay Figure P4.18 A sketch of a flownet under…

A: As per guidelines we need to answer only first question so please repost rest question separately

Q: Water with sp.gr 0.97 flows through a pipe of uniform diameter 350mm with a mean velocity of 1.0…

A: SG = 0.97 D = 350 mm or 0.35 m V = 1 m/sP1 or 250,000 Pa

Q: For the one-dimensional flow system shown below (units in centimeters):a. What is the value of H…

A: Note: The height H is nothing but the upward seepage pressure developed by the water on the soil…

Q: 2. Compute the rate of flow in a pipe with diameter300 mm for a length of 900 meter having a head…

Q: In the figure, suppose that 0= 30°, V₁ = 100 ft/s and the stream is a jet of water with an initial…

A: Given:- θ=30oV1=100 ft/sInitial diameter of jet of water=2 inV2=90 ft/s To find:- (a) The flow rate…

Q: Q.42 "MASS FLOW AT A PIPE JUNCTION Consider the steady flow in a water pipe joint shown in the…

Q: Calculate the water speed in ft/s at point (cross-section) (2). V₂ = eTextbook and Media Save for…

Q: Question 20 There are three pipes and each has different friction or roughness factors below: Saint…

Q: Water flows from reservoir A to B through the three concrete pipes shown below. Assume that concrete…

A: GivenH=20mL1=2500md1=400mm or D1=0.4mL2=1850m, d2=300mm or D2=0.3mL3=800m, d3=200mm or…

Q: Un the igu The head loss irom point 1 to point 2 is 1.50 m and from point 2 to point 3 is 2.40 m.…

A: D=50mm L=8m

Q: 12 m h₁ Ground surface Sheer Pile C h₂ H 36m

Q: 5. Consider the system given below. The diameter of the orifice at the bottom is 5 cm. Determine the…

A: do = 5 cm or 0.05 m Q1 = 10 L/s h = 50 cm or 0.5 m

Q: A horizontal Venturi flow meter consists of a converging-diverging conduit as indicated in the…

A: The volume flow rate Q of a fluid is defined as the flow rate of fluid through a given…

Q: Q.2.8 MASS FLOW AT A PIPE JUNCTION Consider the s. tv low in a water pipc joint shown in the…

Q: 6.88m. Darcy-Weisbach friction factor for all pipes, f=0.0238. Pipe 1: Length=3500m…

Q: Q.2.8 MASS FLOW AT A PIPE JUNCTION Consider the s. v low in a water pipe joint shown in the diagram.…

Q: Water flows through a pipe at 5 L/s as shown. If the gage pressure of 12.5 kPa, 11.5 kPa and 10.3…

Q: There are three pipes and each has different friction or roughness factors below: Saint Pancras…

Q: An 83-mm-diameter siphon is drawing oil (SG = 0.85) from an oil reservoir, as shown in the figure.…

A: Given; Specific gravity of soil, SG=0.85 Head loss from point 1 to point 2=6v22g Head loss from…

Q: -Q.17 MASS FLOW AT A PIPE JUNCTION Consider the steady flow in a water pipe joint shown in the…

Q: There is a leak in a horizontal 30 cm pipeline (f= 0.025). Upstream from the leak two gages 600 m…

Q: For the water distribution system given below, the final corrections are applied and the flow…

A: Given data:-

Q: An ideal fluid with y = 8825 N/m flows in the vertical circular pipe represented below. The flow…

Q: A pipe carrying oil (5G = 0.877) change in size from 150mm diameter in point 1 to 450mm diameter in…

A: Given data, Oil SG = 0.877 Diameter of pipe in section 1 = 150 mm Diameter of pipe in section 2 =…

Q: a. Find an expression for V₂. b. Find the initial time that V₂ first is zero. c. Find the mean…

Q: Shown in figure, A pump discharged 0.05 cu. m/sec. water from a 220 mm suction pipe and delivers it…

Q: H = 1.1 m K = 4.87 x 102 cm/sec 8 = 14° L = 36 m

A: Hydraulic gradient =Loss in headLength of the soilLength of the soil=Lcosθ

Q: As shown in Figure 7, assume that the head loss in the pipe is given by hi = 0.014(L/D)(V 2/2g),…

Q: Q.14.09 MASS FLOW AT A PIPE JUNCTION Consider the steady flow in a water pipe joint shown in the…

Q: Water flows through a pipe at 15 L/s as shown. If the gage pressure of 12.5 kPa, 11.5 kPa and 10.3…

A: The values and figure given in the question are as follows: Discharge through pipe(Q)=15 L/sec…

Q: Add the energy grade line (EGL) as a solid line and the hydraulic grade line (HGL) as a dashed line…

A: The pressure head,

Q: 0.1.15. MASS FLOW AT A PIPE JUNCTION Consider the steady flow in a water pipe joint shown in the…

Q: Subject: Fluid mechanics

A: Given data Discharge at A, QA= 10 ft3/sec QA+QB= 10 ft3/sec …(1) Hence head loss in B and…

Q: 5. Determine the pressure head elevations at B and D and the discharges in the branches in the…

A: From question length and diameter of each pipe is given.Roughness coefficient of each…

Q: 2000 m 45 cm ở Q= 400 litres/s 600 m 30 cm 6 FIGURE D

A: Given that....

Q: Conssier the steady flow in a water pipe joint shown in the diagram. The areas are: A= 0.2 m. Az =02…

Q: Water flows through a pipe at 5 L/s as shown. If the gage pressure of 12.5 kPa, 11.5 kPa and 10.3…

A: Given data, P1 = 12.5 kpa P2 = 11.5 kpa P3 = 10.3 kpa D1= 50 mm D2 = 50 mm D3 = 30 mm Discharge = 5…

Q: In the water network shown in figure,the Hazen-Williams coefficient C for all pipes is 100. a) Using…

A: Take flow in anticlockwise positive, here, flow in AB and BC will be in clockwise but flow in AC…

Q: Three pipes steadily deliver water at 20°C to a large exit pipe in Figure 1. The velocity V; = 5…

A: Given data, Q4 = 120 m³/s V2 = 5 m/s To find out the V1, V3 and V4

Concept explainers

Sediment transport

Sediment transport or Soil transport is the movement of solid particles, usually due to the combination of gravitational forces acting on the sediment, and the movement of the liquid at which the sediment enters. Soil erosion occurs in natural systems where the particles are sandstones (sand, rocks), mud, or clay; the liquid is air, water, or ice; and the gravitational force that works to move particles to the landing surface. Sediment transportation or soil migration due to the movement of liquids occurs in rivers, lakes, lakes, oceans, and other bodies of water as a result of currents and waves. Transportation is also caused by glaciers as they flow, and to places on earth under the influence of wind. Soil erosion due to gravity alone is possible in most sloping areas, including hills, scarves, cliffs, and the continental shelf — the continental boundary of the slope.

Question

Given:(2 decimal places)

h = 1.4

H = 1.1 m

K = 4.87 x 10^-2 cm/sec

θ = 14°

L = 36 m

a.)Find the hydraulic gradient.

b.)Compute the cross-sectional area of the figure in m².

c.)Solve the rate of flow in m³/hr.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Calculate the daily flow in (m³/d) using Darcy's law for a confined aquifer with a hydraulic conductivity of 1.9 (m/d), a thickness of 50 (m) which is 5 (km) wide. Two observation wells are located 1.8 (km) apart in the direction of flow and the head in well 1 is 105 (m) and in well 2 is 95 (m). (Please enter your answer with one decimal)
L = 900m D=35cm L=600m L=900m D=75cm D=60cm L=600m D=30cm L=900m D=40cm A flow rate of 0.5 m³/s is branched into three pipes and then rejoined in the concrete parallel pipes as shown in the figure below. Find the head of loss between point A and point B. Here, the coefficient of friction loss in all tubes is 0.03.
A 56-mm-diameter siphon is drawing oil (SG = 0.818) from an oil reservoir, as shown in the figure. If the velocity of flow in the pipe is 'v, the head loss from point 1 to point 2 is 2v2/2g, and the head loss from point 2 to point 3 is 5v2/2g. Find the absolute pressure (in kPa) at point 2. Use atmospheric pressure, Patm = 101.38 kPa. Use y1 = 2 m., and y2 = 5 m %3D
Consider the one-dimensional open channel flow shown in Figure P10.8. (a) Using the continuity principle and Bernoulli’s equation, show that where F is the local Froude number. (b) Discuss the implications of this result for subcritical flow everywhere, supercritical flow everywhere, and for F = 1 at station 2.
Question 4. The flowrate of the flow is 0,20 m/s in a pipe placed on a horizontal plane. The pipe diameters are as 0.41 m and 0.28 m for Di and D2, respectively. Find the resultant force *(kN) acting to the pipe by the flow. The gauge pressure at (1) is P1 =280 kN/m2. (y= (1) 10KN/m³) Figure 4
i)Calculate the flow rate through the system.
9.14 If the upstream velocity of the flow in Problem 9.13 is U = 1.5 m/s, determine the kinematic viscosity of the fluid. 9.15 Water flows past a flat plate with an upstream velocity of U = 0.02 m/s. Determine the water velocity a distance of 10 mm from the plate at distances of x = 1.5 m and x = 15 m from the leading edge.
Water flows through the branching pipe shown in the figure below. The flowrate at section (1) is Q₁ = 1.1 m³/s, and the velocity at section (2) is V₂ = 17 m/s. A₁ = 0.1 m² P1 = 300 kPa 21 = 0 P3 = -147.2 A3 = 0.035 m² Z3 = 10 m (1) (2) If viscous effects are negligible, determine the pressure at section (2) and the pressure at section (3). P2 = i 315.3 kPa kPa (3) A₂ = 0.03 m² 22 = 0
Do it
Estimate the equivalent hydraulic conductivity for flow in the horizontal direction. Also calculate the ratio of kv(eq)/kH(eq). Suppose that k1 = 15 x10^-4 cm/s, k2= 5.0x10^-4 cm/s, k3= 3.0 x10^-4 cm/s, k4= 2.0 x10^-4 cm/s, H1= 1.0 m, H2 = 2.0 m, H3 =1.5 m, H4 =1.0m. kH(eq) = kV(eq)/kH(eq)=
Water flows through a pipe at 152 L/s that changes gradually in diameter from 196 mm at point A to 456 mm at point B. Point B is 6 m higher than point A. The pressures at point A and point B are 126 kPa and 69.3 kPa, respectively. Assume that the datum line passes through point A. Which of the following most nearly gives the head loss in the pipe? (m). Round your answers in 3 decimal places.
Mato 5