A 56-mm-diameter siphon is drawing oil (SG = 0.818) from an oil reservoir, as shown in the figure. If the velocity of flow in the pipe is 'v', the head loss from point 1 to point 2 is 2v2/2g, and the head loss from point 2 to point 3 is 5v2/2g. Find the absolute pressure (in kPa) at point 2. Use atmospheric pressure, = 101.38 kPa. Use y1 = 2 m., and y2 = 5 m Patm

A 56-mm-diameter siphon is drawing oil (SG = 0.818) from an oil reservoir, as shown in the figure. If the velocity of flow in the pipe is 'v', the head loss from point 1 to point 2 is 2v2/2g, and the head loss from point 2 to point 3 is 5v2/2g. Find the absolute pressure (in kPa) at point 2. Use atmospheric pressure, = 101.38 kPa. Use y1 = 2 m., and y2 = 5 m Patm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

please solve in SI units
What flows through a 0.305m vertical pipe downwards at a rate of 1.70 x 10^(-4) m^3/s exiting into the atmosphere. the pipes diameter remains constant at 0.013m. The velocity at the exit of the pipe was measured to be 1.28 m/s. Determine the pressure at the top of the pipe.
8. Calculate the pore water pressure at point A through I shown on the following flow net. 14 m 10 m CDEFGH
4. The siphon shown is 76 mm in diameter. It draws oil from a large tank. The loss of head up to the summit is 6 cm and from the summit to the exit is 23 cm of oil. a. Calculate the exit velocity. b. Calculate the pressure at the summit. 0.6 8.3 76- mm 0 siphon
7. What is the pressure value (PA) needed to achieve equilibrium for the figure shown (kPa)? a. 0.59 c. 1.02 b. 1.02 d. None of all these PA S.G=0.87 30 120 mm
Consider the tank shown in (Eigure 1). Take po = 900 kg/m³, Pu=1000 kg/m³, and pHg = 13 550 kg/m³. 0.6 m 0.8 m 100 mm h 1 of 1 > P Part A Determine the level of water in the tube if the depths of ol and water in the tank are 0.6 m and 0.8 m. respectively, and the height of mercury in the tube is h=0.075 m A Express your answer to three significant figures and include the appropriate units. PA h = 240 Submit + Provide Feedback → OF ? mm Previous Answers Request Answen X Incorrect; Try Again; 4 attempts remaining Next > 1231 AM 0
Q2: Compute the value of (H) in centimeters such that the pressure at B is 90% of the pressure at point A. If the pressure at A is 79.4 kPa, S.G (oil)=0.89, S.G (mercury)=13.6. SAE 30 oil Gage B Mercury- 6 сm H Water flow 11 cm 4 cm
Determine (a) the magnitude and (b) direction of the anchoring force needed to hold the horizontal elbow and nozzle combination shown in the figure below in place. Atmospheric pressure is 97.1 kPa. The gage pressure at section (1) is 103 kPa. At section (2), the water exits to the atmosphere. Assume p₁ = 103 kPa, V₁ = 4 m/s. (a) Kx = i 2260.24 (b) to the left N V₂ 160 mm Section (2) 300 mm V₁ Water Section (1) P1 V₁
Consider the pressurized horizontal pipe network shown below. Pipe 2 is arranged in parallel with Pipe 3. The characteristics of each pipe are summarized in the table. The flow of water at Node A is Q = 10 cfs and the pressure head at Node A is yA = 180 feet. The temperature of the water is 60° F. a) Determine the flow in cfs in Pipe 2. b) Determine the flow in cfs in Pipe 3. c) Determine the friction head loss hric in feet in Pipe 1. d) Determine the friction head loss hfic in feet in Pipe 2. e) Determine the friction head loss htric in feet in Pipe 3. f) Determine the friction head loss hfric in feet in Pipe 4. g) Determine the pressure head ys in feet at Node B. h) Determine the pressure head yc in feet at Node C. i) Determine the pressure head yo in feet at Node D. Flow Friction Pressure Diameter Length Pipe (inches) (feet) Friction (cfs) head Нead factor f Kpipe loss (feet) Node (feet) 1 16 500 0.012 10 A 180 12 1000 0.014 B 10 1000 0.015 16 500 0.020 10 D Pipe 2 Node Node Node…
Consider the pressurized horizontal pipe network consisting of three pipes arranged in series. The characteristics of each pipe are summarized in the table. The flow of water at Node A is Q = 5 cfs and the pressure head at Node A is yA = 200 feet. The temperature of the water is 60° F. a) Determine the friction head loss hfric in feet in Pipe 1. b) Determine the friction head loss hfric in feet in Pipe 2. c) Determine the friction head loss hfric in feet in Pipe 3. d) Determine the pressure head ys in feet at Node B. e) Determine the pressure head yc in feet at Node C. f) Determine the pressure head yo in feet at Node D. Flow Friction Pressure Diameter Length Friction (feet) (cfs) head Нead Pipe (inches) factor f Kpipe loss (feet) Node (feet) 1 16 500 0.011 5 A 200 2 12 1000 0.013 B 3 10 750 0.015 D Node Node Node Node A в D 5 cfs 5 cfs Pipe 1 Pipe 2 Pipe 3
Please show all work including unit converstions and please make sure to show all units. For P1=10+(6), so P1=16 psi for P2=20+0, so P2=20 psi for D1= 1ft for D2=0.6ft for Q=5.4 cubic ft per second
A reservoir contains two different fluids is shown in the figure. The height of the water is 8 m, and the height of the oil (SG = 0.86) is 4 m. a. Determine the density of the oil. b. Determine the pressure between the oil and water in kPa. C. Determine the pressure at the bottom of the reservoir in kPa. OIL WATER