Governor has all four arms 440 mm long. The upper arms are attached on the axis of rotation and the lower arms are attached to the sleeve at a distance of 2.5 Cm from the axis. The mass of each ball is 8.5 kg and the sleeve has a mass of 30 kg. The extreme radii of rotation are 20 Cm and 33 Cm. Determine the range of speed and Sensitiveness of Governors.

Governor has all four arms 440 mm long. The upper arms are attached on the axis of rotation and the lower arms are attached to the sleeve at a distance of 2.5 Cm from the axis. The mass of each ball is 8.5 kg and the sleeve has a mass of 30 kg. The extreme radii of rotation are 20 Cm and 33 Cm. Determine the range of speed and Sensitiveness of Governors.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

38
Using the figure shown, and initial displacement of 2.5 mm and it starts from rest and the motion of the 5 kg block as the generalized coordinate.Determine:a. mass, spring, damping equivalentb. damping ratioc. logarithmic decrement and overshoot of the system
In a satellite model for a science project, given the masses of the three satellites m=1.8 kg, mg= 4 kg, and m.=5 kg that are connected with massless rods, joined at the point the rotation axis is passing through. The satellites have the distances rad R=1.5 m, R = 1 m, and Rc=2 m, from the rotation axis. The system rotates with an angular speed w = 2.7 mA RA RB RC mc 1. Calculate the moment of inertia I; for this model: /, = kg m2 m2 kg 2. Calculate the magnitude of the angular momentum L, = 3. Calculate the rotational kinetic energy K, = J 4. As the system is rotating counter-clockwise the direction of the vector is The mass mc was not properly glued and breaks away during the rotation. 1. Calculate the moment of inertia /f for this model now. If= |kg m2 2. Using the conservation of angular momentum, calculate the angular speed wf after the mass m, has broken away during rad the rotation. Wf= 3. Calculate the rotational kinetic energy in this situation: K=
25
A Net Torque of 25 Nm is applied to the edge of a flat disc at rest with a mass of 5.00 kg and a radius of 0.50 m. Calculate how many revolutions it will complete before it reaches an angular speed of 10 rpm.
The roller is pushed forward with a force of 200 N when the handle is at 45°. The friction coefficients between the roller and the ground are μ = 0.12 and k = 0.1. If the roller has a mass of 80 kg and a moment of inertia of 2.45 kg m² about its center of mass, calculate the magnitude of the angular acceleration of it. Present your answer in rad/sec² using 3 significant figures. MARANANLA G 45° 200 mm A 200 N
A flywheel of mass 125kg and radius of gyration 150mm is accelerated from rest to a speed of 1180rpm whilst making 500 revolutions. The motion is resisted by a friction torque of 2.5Nm. Determine the work done and the maximum power developed by the driving motor.
The accelerating torque increases the speed of a flywheel from x rpm to y rpm in 15 seconds. Find 1. The accelerating torque produced during the above period. 2. Increase in the kinetic energy of the flywheel 3. Change in the angular momentum of the flywheel. 4. Number of revolutions made by the flywheel during this period. 5. Find the braking torque required to stop the flywheel completely. Assume suitable mass and radius of gyration. Also assume suitable values for rpm x and y above.
i need correct and stepwise answer i surely give you 3 likes
A drum can rotate about a fixed-point O. The A block is attached to a cord wrapping around the drum. The mass of the drum is md = 100kg and the radius is r = 0.5 m. The radius of gyration of the drum about point O is ko=0.3 m. The mass of the block is mb= 20kg. The block is released from rest. The acceleration due to gravity is g=9.81 m/s2. (1) Calculate the mass moment of inertia of the drum about the point O, IO_______(kgm2) (two decimal places)
A ball governor of the vertical compression spring type runs at a mean speed of N = 189.228 rev/min. The bell crank lever arms are a = 0.158 m and b = 0.063 m and the rotating balls have a mass of m = 2.793 kg each, and the ball radius is r = 0.114 m at the mean speed. Part A: If the speed range of the governor at the mean speed is A = 1.287 rev/min, determine the friction force Fu at the sleeve (neglect the effect of gravity on the balls). Part B: Determine the spring stiffness S that would be required to make the governor isochronous if the sleeve lift is y = 0.013 m from the mean position (assume the ball arm is vertical at the mean position).