The turning-moment diagram for an engine, which has been drawn to scales of 1 mm to 50 Nm and I mm to 1° of rotation of crankshaft, shows that the greatest amount of energy which has to be stored by the flywheel is represented by an area of 2250 mm 2. The flywheel is to run at a mean speed of 240 rpm with a total speed variation of 2 per cent. If the mass of the flywheel is to be 450 kg, determine suitable dimensions for the rim, Cast iron has a density of 7.2 Mg/m3.

The turning-moment diagram for an engine, which has been drawn to scales of 1 mm to 50 Nm and I mm to 1° of rotation of crankshaft, shows that the greatest amount of energy which has to be stored by the flywheel is represented by an area of 2250 mm 2. The flywheel is to run at a mean speed of 240 rpm with a total speed variation of 2 per cent. If the mass of the flywheel is to be 450 kg, determine suitable dimensions for the rim, Cast iron has a density of 7.2 Mg/m3.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A box of mass m = 0.7 kg is attached to a rope which is wrapped around a physical pulley with a radius of R = 10.2 cm and a rotational inertia of I = 0.075 kg·m2. When the box is released it starts to fall down with a constant acceleration and, at the same time, the pulley starts to spin up, see the picture below. Assuming that the pulley is frictionless, what is the magnitude of the box's acceleration and what is the tension in the rope? The acceleration of the box, a ? The tension in the rope, T? If the box starts from rest and traveled downwards a distance of h = 28 cm, what is the speed of the box and what is the angular velocity of the pulley? The speed of the box, v =? The angular velocity of the pulley, ω? -------------------------------------------------------------- A Merry Go Round carousel has a radius of R = 2.4 m and a rotational inertia of I = 695 kg·m2. A 75‑kg student is on the carousel at the midpoint between the carousel's center and the rim (at R/2 distance from…
. An object of mass 12 kg is suspended from a pulley which has a mass of 6 kg and a radius of rotation of 0.25 m. If at that time the pulley rotates with an angular velocity of 5 rad/s, we want to know that when the object moves down a distance of 2 m, then at what speed is the pulley rotating? If the friction force on the pulley bearing produces a moment of resistance of 2 N-m 12 kg 0.3 m
The crude-oil pumping rig shown is driven at 20 rpm. The inside diameter of the well pipe is 2 in., and the diameter of the pump rod is 0.75 in. The length of the pump rod and the length of the column of oil lifted during the stroke are essentially the same, and equal to 6000 ft. During the downward stroke, a valve at the lower end of the pump rod opens to let a quantity of oil into the well pipe, and he column of oil is then lifted to obtain a discharge into the connecting pipeline. Thus, the amount of oil pumped in a given time depends upon the stroke of the lower end of the pump rod. Knowing that the upper end of the rod at D is essentially sinusoidal with a stroke of 45 in. and the specific weight of crude oil is 56.2 lb/ft3 determine (a) the output of the well in ft3. /min if the shaft is rigid, (b ) the output of the well in ft3 /min if the stiffness of the rod is 2210 N/m, the equivalent mass of the oil and shaft is 290 kg, and damping is negligible.
A brake test is carried out with a balance and a direct current motor. The purpose of this experiment is to calculate the torque on the motor shaft. The following values were obtained in the experiment. U=220 volts., I=107 amps, n = 1200 rpm. The length from the axis of the motor shaft to the point where the brake lever presses on the scale is L=80 cm. and the weight read on the balance G = 20 Kg. is Accordingly, calculate the following values: a) the shaft power taken from the shaft of the motor, b) the electrical power drawn by the motor from the mains c) motor total losses and motor efficiency Calculate
A steel ring was shrunk into the outside of a hollow steel disc. The interference radius of the assembly is 40 mm whilst its outer and inner radii are 250 mm and 20 mm, respectively. If the angular speed at which the ring-disc assembly becomes loose is 401.8 rad/sec, determine the shrink-fit pressure at the mating surface of the assembly? Assume that Poisson's ratio for steel is 0.3 and its density is 7860 kg/m³.
A В X Figure 3 Refer to Figure 3. A slender rod of mass 1.5 kg and length L = 1 m is pivoted at one end as shown. It is released from rest in a horizontal position and swings freely. At the instant it is released the angular acceleration (alpha) is 14.715 rad/s^2. In the question that follows, select the answer that is closest to the true value. What is the force reaction at the pivot in the y-direction at the instant the rod is released (when it is still horizontal) in units of N ? Answers: A) 3.68 B) 4.91 C) 6.13 D) 7.36 --- O A O B O D
A spur pinion of pitch diameter 50 mm rotates at 200 rad/s and transmits 3 kW power. The pressure angle of the tooth of the pinion is 20°. Assuming that only one pair of the teeth is in contact, the total force (in Newton) exerted by a tooth of the pinion on the tooth on a mating gear is
A force of 100N is applied to the centre of a circular disc, of mass 10 kg and radius 1m, resting on a floor as shown in the figure. If the disc rolls without slipping on the floor, the linear acceleration (in m/s2 ) of the centre of the disc is ______
The roller is pushed forward with a force of 200 N when the handle is at 45°. The friction coefficients between the roller and the ground are μ = 0.12 and k = 0.1. If the roller has a mass of 80 kg and a moment of inertia of 2.45 kg m² about its center of mass, calculate the magnitude of the angular acceleration of it. Present your answer in rad/sec² using 3 significant figures. MARANANLA G 45° 200 mm A 200 N
A flywheel of mass 125kg and radius of gyration 150mm is accelerated from rest to a speed of 1180rpm whilst making 500 revolutions. The motion is resisted by a friction torque of 2.5Nm. Determine the work done and the maximum power developed by the driving motor.
Two blocks 1 and 2 are connected by a rope over a pulley as shown. The pulley is very light (massless) and rotates with essentially no friction. Calculate the mass of block 1, m1, given that the mass of block 2 is m2=5.5 kg and that block 2 moves and accelerates downwards at 3.57 m/s2 when θ=35∘ and μk=0.4. I think that I need to be using Newtons second law but I just dont know how to solve this. Can you please help?
A uniform rod of mass M = 2.3 kg and length L = 0.2 m, lying on a frictionless horizontal plane, is free to pivot about a vertical axis through one end, as shown. The moment of inertia of the rod about this axis is given by 1/3 ML2. If a force F = 7 N, q = 47° acts as shown, what is the resulting angular acceleration (in rad/s2) about the pivot point?