HW2Governor has all four arms 350 mm long. The upper arms are attached on the axisof rotation and the lower a attached to the sleeve at a distance of 20 mmrms arefrom the axis. The mass of each ball is 6 kg and the sleeve has a mass of 45 kg.The extreme radii of rotation are 150 mm and 230 mm. Determine the range ofspeed and Sensitiveness of Governors.

Answered: Image /qna-images/answer/5bff9d26-4125-4449-91c0-beab3ee1b0cc.jpg

Governor has all four arms 350 mm long. The upper arms are attached on the axis of rotation and the lower arms are attached to the sleeve at a distance of 20 mm from the axis. The mass of each ball is 6 kg and the sleeve has a mass of 45 kg. The extreme radii of rotation are 150 mm and 230 mm. Determine the range of speed and Sensitiveness of Governors.

Governor has all four arms 350 mm long. The upper arms are attached on the axis of rotation and the lower arms are attached to the sleeve at a distance of 20 mm from the axis. The mass of each ball is 6 kg and the sleeve has a mass of 45 kg. The extreme radii of rotation are 150 mm and 230 mm. Determine the range of speed and Sensitiveness of Governors.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Determine the equivalent of the system using the linear motion of the thin disk 2k 3. Slender bar of…

Q: Determine the equivalent of the system using the angular motion of t 2k

Q: Each spring of a Pickering governor of a gramophone is 8mm wide and 0.15 mm thick with a length of…

A: Given data as per question width =8 mm Thickness =0.15 mm Length =50 mm Mass =50 g The ratio of the…

Q: The arms of a Proell governor are 275 mm long and are pivoted on the axis of rotation. The…

A: The answer is in next slide

Q: T Tolls without slipping on horizontal floor. For 23. For the system shown in figure, the disc of…

Q: Derive the differential equation of motion for the system shown in Figure (). Neglact the mass of…

Q: The system shown below is made up of two pulleys attached to the same shaft, with radii ri and re of…

Q: Determine the tension developed in

A: Given: m=20 kg kinetic friction=0.3 s=6 m t=3 s To determine: Tension developed in the cable

Q: 3. Determine the equilibrium position, and the angular frequency of the system shown. The masses and…

A: Consider a free body diagram:Here, is the tension and deflection in wire.Consider be the initial…

Q: Calculate the speed of the flywheel/clutch assembly after engagement.

A: m1=950kgk1=135mm=.135mm2=1000kgk2=90mm

Q: 1. Part (1): 4.5 kg wheel has an outer radius of 480 mm rolls down an incline starting from rest.…

Q: A 500 pound weight is attached to a cable that is being lifted by a 10 inch diameter drum. The 48V…

A: GIven data: The diameter of the drum is d=10 in The weight attached to the cable is Ft=500 lb The…

Q: Assuming there is no slippage for the belt assembly below, Determine the following: (a) What is…

Q: Determine the shortest time it takes the car to reach a speed of v= 72.0 km/h, starting from rest,…

Q: Governor has all four arms 430 mm long. The upper arms are attached on the axis of rotation and the…

Q: How do I solve problem number 3?

A: Step 1:Step 2:Step 3:

Q: what is the answer to this

Q: Problem 2: In the speed-governing mechanism m = 0.2kg. L = 10 cm (rods AB have negligible mass), w =…

Q: Part A- Angular Acceleration of the Rod Learning Goal: The slender rod AB shown has a mass of m =…

Q: adius of 10.5 cm. Due to the mal adjustment of spring, the equilibrium speed of governor at top…

Q: a) The length of the arms of a Porter governor is 300mm long. The upper and lower 10 arms are…

Q: e top arms make 45° with the axis of rotation in the equilibrium position, find the range of speed…

A: M=mass of contol load=18 kgm=mass of ball =2kgF= friction =14Nh= height of governorcos 45 =h250from…

Q: A ball governor pe rev/min. The bell-crank lever arms are 150 mm and 75 mm an e a mass of 2.75 kg…

A: Vertical arm kength(a)=150 mm Horizontal arm length, b=75 mmSpeed range of governer at mean speed…

Q: The rotor of a gas turbine is spinning at a speed of 5,700 rpm when the turbine is deactivated. It…

A: First we will calculate the initial angular velocity from given rom and then calculate the angular…

Q: Question 2 A car has a mass of 4 Mg and the center of mass at G = 400mm from the ground. The front…

A: Draw the free-body diagram of the car with wheels. Apply force equilibrium in a vertical…

Q: A uniform disc of 25-kg mass and 500-mm diameter is mounted on a shaft. The plane of the disc is not…

A: Data given- m = 25 kg d = 500 mm r = 500/2 = 250 mm = 0.25 m θ = 2.5° N = 1000 rpm

Q: Please use the Rigid Bodies method from vector dynamics.

A: The system consists of a cart with mass M, four wheels each with mass m/2, and two axles. The front…

Concept explainers

Clutches, Brakes, Couplings, and Flywheels

The clutch is described as a machine element used to connect or disconnect two shafts together to transmit torque or power. The clutch works on the principles of friction. The clutch is commonly used in automobiles to transfer power from the driving shaft to the driven shaft.

Question

HW2
Governor has all four arms 350 mm long. The upper arms are attached on the axis
of rotation and the lower a attached to the sleeve at a distance of 20 mm
rms are
from the axis. The mass of each ball is 6 kg and the sleeve has a mass of 45 kg.
The extreme radii of rotation are 150 mm and 230 mm. Determine the range of
speed and Sensitiveness of Governors.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Clutches, Brakes, Couplings and Flywheels

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Each arm of aporter govern or is 250 mm long The uppe r and ower arms are pivoted at 40mm and 50 mm respectively from axis of rota tion Each ball has mas s Df 5 kg and the sleeve mass is 50kg The friction force on the sleve is 40 N. Determine the range of the speed of governor for extreme radii of rota tion of 125 mm and 150 mm
Determine the time required to accelerate a countershaft of rotating mass 520 kg and radius of gyration 150 mm to the full speed of 360 rpm from rest through a single clutch. The internal and external radii are 120 mm and 180 mm. Take friction coefficient as 0.3 and the spring force (W) as 660 N. Assume that only one side of clutch is effective.
A steel ring was shrunk into the outside of a hollow steel disc. The interference radius of the assembly is 40 mm whilst its outer and inner radii are 250 mm and 20 mm, respectively. If the angular speed at which the ring-disc assembly becomes loose is 401.8 rad/sec, determine the shrink-fit pressure at the mating surface of the assembly? Assume that Poisson's ratio for steel is 0.3 and its density is 7860 kg/m³.
The torque of the screw jack is 100 N-m and its speed is 30 rpm. Evaluate power of the device
The radius of the pulley is of inertia is I = 0.1 kg-m2. R = 100 mm The mass stant is k = 135 N/m. m = 5 kg. and its moment The spring conThe system is released from rest with the spring unstretched. What maximum distance does the mass fall before rebounding?
i need correct and stepwise answer i surely give you 3 likes
A drum can rotate about a fixed-point O. The A block is attached to a cord wrapping around the drum. The mass of the drum is md = 100kg and the radius is r = 0.5 m. The radius of gyration of the drum about point O is ko=0.3 m. The mass of the block is mb= 20kg. The block is released from rest. The acceleration due to gravity is g=9.81 m/s2. (1) Calculate the mass moment of inertia of the drum about the point O, IO_______(kgm2) (two decimal places)