GivenThe figure shows a pump delivering 700 L/min of oil (sg - 0.8a) from an undergroundstorage drum to the first stage of a processing system.hi - 1.55h2 - 9.90h3 - 3.35Air pressure - 725RequiredIf the total energy lass in the system is 5.55 Nem/N of ail flowing, calculate thepower delivered by the pump in kW, to the nearest 100th.Air iven kPahiFlowPumpSuctionPipe-DN 65Schedule 40

Answered: Image /qna-images/answer/34c0d01a-c5d6-4e0c-97c8-6c55b64c33fb.jpg

Given The figure shows a pump delivering 700 L/min of oil (sg - 0.8a) from an underground storage drum to the first stage of a pracessing system. h1 - 1.55 h2 - 9.90 ha - 3.35 Air pressure - 72s Required If the total energy loss in the system is 5.55 Nem/N of ail flowing, calculate the power delivered by the pump in kW, to the nearest 100th. Air iv Flow Pu Suction Pipe DN 65 Schedule 40

Given The figure shows a pump delivering 700 L/min of oil (sg - 0.8a) from an underground storage drum to the first stage of a pracessing system. h1 - 1.55 h2 - 9.90 ha - 3.35 Air pressure - 72s Required If the total energy loss in the system is 5.55 Nem/N of ail flowing, calculate the power delivered by the pump in kW, to the nearest 100th. Air iv Flow Pu Suction Pipe DN 65 Schedule 40

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For the tank, calculate the volumetric flow of water, exiting the nozzle. the tank is sealed and there is a pressure of 20 psig on the water. depth h is 8 feet
HMW-1 Regenerative steam power plant shown in figure below employs two feed heaters which are optimally placed such that cycle has the maximum thermal efficiency. The mass of steam generated is 16 kg/s. The feed water leaves each heater as saturated liquid at corresponding bleed pressure. Neglect the pumps work and find: a. Cycle thermal efficiency. b. Specific steam consumption. c. Mechanical efficiency of the turbine-generator gearing unit. Draw the equivalent (T-s) diagram considering an ideal cycle. 70 bar 450°C Gearing unit Generator 15 MW Turbine Super heater Boiler Condenser 0.07 bar Оpen heater Closed heater Pump Pump Throttling Valve
11 Estimate the kilowatt pump you would need to pump 450 Liter/min of liquid water at 20 °C through a rise in elevation °C of 100 m. Assume the water is pumped adiabatically and with negligible changes in temperature and kinetic energy. [ans: -7.355 kW]
1. A Rankine cycle with reheating has a throttle pressure of 135 bars at the turbine inlet and 28 bars reheat pressure, the throttle and reheat temperature of the steam is 550C, condenser pressure is 0.035 bar, mass flow rate of steam is 10 kg/sec. Draw the T-s and schematic diagram of the cycle and determine the following: (c) theoretical thermal efficiency (d) the steam rate (e) heat rate of the cycle
One single phase energy meter operating on 230 V and 5 A for 5 hours makes 1940 revolutions. Meter constant in revolution is 400. The power factor of the load will be:
the 9.63. When glycerin (25°C or 77°F) flows through a 30 m (100 ft) length of 75 mm (3 in.) pipe, the head loss is 36 m (120 ft). Calculate the flowrate. 9.64. A pump of what power is required to pump 40 1/min of crude oil from a tank of surface elevation 12 to one of elevation 18 through 450 m of 75 mm pipe, if the oil is at (a) 25°C, (b) 40°C?
An ESP is to he designed to treat 9000 m3/min of gas to remove particles at 99.8% efficiency. Using Figure 5.10, estimate the required corona power in kW.
Suppose the pump of Fig. is situated between two water tanks with their free surfaces open to the atmosphere. Which free surface is at a higher elevation—the one corresponding to the tank supplying water to the pump inlet, or the one corresponding to the tank connected to the pump outlet? Justify your answer through use of the energy equation between the two free surfaces.
An insulated piston-cylinder device contains 4 L of saturated liquid water at a constant pressure of 200 kPa. Water is stirred by a paddle wheel while a current of 8A flows for 50 min through a resistor placed in the water. If one-half of the liquid is evaporated during this constant-pressure process and the paddle-wheel work amounts to 300 kJ, determine the voltage of the source. Also, show the process on a P-v diagram with respect to the saturation lines.
A constant-area duct that is 20 cm in length by 2 cm in diameter is connected to a reservoir through a converging nozzle, as shown in Figure 9.13. For a reservoir pressure and tem- perature of 1 MPa and 500 K, determine the maximum air flow rate in kilograms per sec- ond through the system and the range of back pressures over which this flow is realized. Repeat these calculations for a converging nozzle with no duct. Assume that fis equal to 0.032 and that y - 1.4. f= 0.032 D-2 cm Isentropic flow P1,000 kPa I 500 K 20 cm