given: T, 38o'k, P= 110 KPa Tェ-680K ュー500K Pa %3D Cv=0.7 KJ K8-K Charge in specitic entropy a the ideal gas om s tate State 2 ? %3D

Q: The progressive or gradual engagement of the teeth of helical gears gives the ability to transmit…

A: Given data: The progressive or gradual engagement of the teeth of helical gears gives the ability to…

Q: How much force in lbs will it take to lift a 10 -lb weight with a wheel and axle, when the axle is…

A:

Q: The pictured disk which weighs 20 lbs. and contacts an inclined surface (this inclined surface is…

A:

Q: The radial distance measured from the pitch circle of a gear to the top of the gear tooth is known…

A:

Q: What is the module of a spur gear with 30 teeth and pitch diameter if 5 inches? 5.236 mm 4.233 mm…

A: The given values are -  Teeth T =30 Pitch diameter D = 5 inch(127 mm)

Q: The distributed load of w = (-2x² + 4x + 16) lb/ft acts on the beam as shown(Figure 1). Part A…

A:

Q: 04/ Determine suitable groove dimensions for a 0101-16 '0' ring to seal against a solid cylinder.

A: Given that ,  Determine suitable groove dimension for a 0101-16 'O' ring to steal against a solid…

Q: In the scale of inches, draw material edge at 7.00 diameters with six holes at 50 diameters. The six…

A:

Q: 4 = 2, B= 3, and the angle formed by A and B is 60°. Calculate the value of 4+ 2B. Round your answer…

A:

Q: find the requird fillet Size Ch) for figew soンル2 ん。 レン46cm 26cm /2

A: Given data: -  The shear stress for all joints is τ = 0.5 MPa. The length L is L = 40 cm. The…

Q: The steel box wrench (E=29,000ksi, v=0.32) is loaded with a 40-lb horizontal force and a 25-lb…

A:

Q: R.75 00.63 THRU $5 01.123 0.250 E 1.38 0.63 mm radius hole partially through the part 0.63 mm radius…

A:

Q: Determine the mass of a steel ball whose diameter is 16mm.

A:

Q: A gear train consists of three gears: a pinion (which is the driver), an idler, and a gear (which is…

A: Given:- The gear train of three gears Tidler=68  Tidler(to replace)=37 To find:- Velocity ratio…

Q: Calculate y, the distance from the base to the position of the Neutral Axis of the T-section shown…

A:

Q: 1. If the block is loaded with P = 282 kN, calculate the required dimension "b" of the key.   Write…

A:

Q: The horsepower (hp) that a shaft can safely transmit varies jointly with its speed (in revolutions…

A:

Q: Using the figure below solve for the desired degrees to be set in the compound rest. I TPF = .602…

A:

Q: Give the horizontal and vertical distances from the upper left corner of this part to the center of…

A: The depth and dimension for the slot is 0.243 and for chamfer 0.089 depth. Hole A X…

Q: The objects shown below have been rotated positively about one of the axes shown. the amount of…

A: According to the given data rotation amount and rotational axis is provided in the below picture.

Q: The radial distance measured from the pitch circle of a gear to the bottom of the gear tooth is…

A:

Q: QUESTION 2 A shaft rotates at 300 rpm. 1), If it carries a spur gear that delivers 5 hp to a mating…

A: Given: N=300 rpm

Q: olve show full solution

A: To find:The principle stress at point A and absolute maximum normal stress at and absolute maximum…

Q: The answer is one of the options below please solve carefully and circle the correct option Please…

A: Given Gear train arrangement To find Gear train which will be effective for bearing

Q: In the gear train shown gear 3 is carried on arm 5, Gear 3 meshes with gear 2 and gear 4. The number…

A: Here, Gear 2 is sun gear. Gear 3 is planet gear. Gear 4 is annular gear. Link 5 is arm.   From the…

Q: The radial distance measured from the pitch circle of a gear to the bottom of the gear tooth is…

A: As per given question  The radial distance measured from the pitch circle of a gear to the bottom…

Q: A hollow tube with thickness t = 1/4 in. is applied with a tensile load of 33 kips. Compute its…

A: Given data,  Tensile load P= 33kips = 33000 lbs  t= 1/4 in  Tensile stress S= 12 ksi = 12000 lb/in²…

Q: 3. From the given figure, solve for the bar X from the reference line (choose the nearest answer)

A:

Q: Solve for the resultant force.

A:

Q: Please now solve 3

A: this question is based on the concept of material science.