Given multi story building of 20 x 20m area as shown in the sketch, design the slabs according to AC 1318-19 using the direct design method, the building supposed to be used as office building. (Live load =1kN/m²) Assume that the ultimate compression strength of concrete is 25 MPa and the steel yield stress is 420 MPa, the thickness of the slab is 160 mm, check if Direct design method is applied, and check hmin for corner panel. a 2.0m 6.0m 6.0m 6.0m Section a-a Dimension of column = 400 x 400 mm Dimension of beam = 650 x 300 mm Dimension of slab = 160 mm 2.0m 6.0m 6.0m 6.0m 6.0m wo'g

Given multi story building of 20 x 20m area as shown in the sketch, design the slabs according to AC 1318-19 using the direct design method, the building supposed to be used as office building. (Live load =1kN/m²) Assume that the ultimate compression strength of concrete is 25 MPa and the steel yield stress is 420 MPa, the thickness of the slab is 160 mm, check if Direct design method is applied, and check hmin for corner panel. a 2.0m 6.0m 6.0m 6.0m Section a-a Dimension of column = 400 x 400 mm Dimension of beam = 650 x 300 mm Dimension of slab = 160 mm 2.0m 6.0m 6.0m 6.0m 6.0m wo'g

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

ve st Semest desi Q4) Concrete is required for walls of a building that will be moderately exposed to Intrained freezing and thawing. The cross section of a wall is 300 x 1500 mm. The smallest spacing between reinforcing steel is 50 mm. The specified compressive strength of Compressive strengthe 3 concrete at 28 days is 21.5 MPa and a slump of 50 mm. Portland cement type I is used with specific gravity of 3.15, maximum size of aggregate 25 mm and fineness modulus of fine aggregate is 2.4, absorption capacity and moisture content of fine aggregate are of 0.8%, and 1.75% respectively. The dry-rodded unit weight of coarse aggregate is 1650 kg/m³, absorption capacity and moisture content of coarse aggregate are of 0.8%, and 1.75% respectively. Both aggregates have a bulk specific gravity (SSD) of (2.65. The aggregates conform to the ASTM C33-84 requirements for grading. Estimate the quantity of (cement, fine aggregate, coarse 94 8.75 aggregate and water) for 1m³ concrete. Tooox 2.65 alka…
PROBLEM TO SOLVE: 600 mm 400 mm -6-25mm diam. Using fe' = 28 MPa, Mmax = +320 kNm Determine the following: d. Moment of Inertia under critical condition e. Demand Capacity Ratio of Concrete under Compression Stress f. Compression force on concrete (KN) g. Distance of the compression concrete force from the neutral axis (mm)
0 ww C. 6.31 A concrete mix includes the following ingredients per cubic foot: a. Cement = 25 lb b. Water = 11 lb c. No admixture Table P6.31 shows possible changes that can be made to the mix ingredi- ents. Indicate in the appropriate boxes in the table what will happen in each case for the workability and the ultimate compressive strength as increase, decrease, or approximately the same. TABLE P6.31 to dignope Cement (lb) 25 28 25 25 25 25 25 amigur Water (lb) 15 11 11 8 11 11 11 Admixture None None Water reducer Water reducer Superplasticizer Air entrainer Accelerator What Will Happen? www.10345 Ultimate Compressive we Strength Workability
What would be the average compressive strength of concrete if the load at failure of the 3 trials are 55, 100 kg, 54, 800 kg, and 55, 200 kg. Diameter of the sample is 6”. a 31.1 MPa b 30.1 MPa c 30.6 MPa d 30.6 MPa
Controlling excessive temperature gradients in large concrete masses is verycrucial. Explain in your own words four such methods available to minimize thetemperature gradient.
Write discussion about Compressive strength of cube and Cylinder concrete specimens.
A flexure strength tests were performed on a concrete beam having a cross section of 0.15x0.15m and a span of 0.45m. If the total load at failure was 37.5kN, calculate the ff:a. The flexure strength of the concrete if center-point was applied.b. The flexure strength of the concrete if third-point was applied.c. Which of the two flexural tests is recommended in determining the flexure strength of the concrete and why?
Please fast
A concrete masonry unit has actual gross dimensions of 190 mm X 190 mm X190 mm. The unit is tested in a compression machine with the followingresults:Maximum failure load = 370 kNNet volume = 5125 cm3a. Is the unit categorized as solid or hollow? Why?b. Calculate the gross area compressive strength.c. Calculate the net area compressive strength.
Subject: Pre-stressed Concrete Design (Civil Engineering) Note: NSCP (2015)
Reinforced concrete
Q: Abeam with rectangular cross-section of (300 x600).mm dimensions, reinforced with 4 bars of 20 mm. The concrete in compression Zone arrived the fracture (Ecu=0.003). The yielding stress of the rebar is 420 NImm?. f- 28 NImm?. Assume linear distribution for strains. %3D ナ Concrete couer is 40 mm. Find :- 1) The strain ia steel reinforcing bars. 2) The positionof neutral axis from the top of the beam (Cdistance). 3) Are reinforcement bars yield or not ? 4) The position of neutral axis from the top in case of balanced failure. 5) Is the beam under, over or balanced reinforcement ? 6) The compression force in cancrete. 7) The tensile force in steel reinforcing bars 8) Check the spacing between longitudiaal bars according to ACI requirements, with sketch.