Given dF₁/dP₁-2+0.024P, and dF2/dP₂ - 1.2+0.016P₂. For a load of 200 MW, the economic dispatch was found at P1 = 60 MW and P2 = 140 MW with λ = 3.44 $/MWh. Irrespective of the units power limits, if the load increases to 220 MW, and the Base Point & Participation Factors method is used, the new generation of the units will be: Select one: O a. P1, new = 65 MW, and P2, new = 155 MW O b. None of these C. P1, new = 68 MW, and P2, new O d. P1, new = 78 MW, and P2, new = 152 MW = 142 MW

Given dF₁/dP₁-2+0.024P, and dF2/dP₂ - 1.2+0.016P₂. For a load of 200 MW, the economic dispatch was found at P1 = 60 MW and P2 = 140 MW with λ = 3.44 $/MWh. Irrespective of the units power limits, if the load increases to 220 MW, and the Base Point & Participation Factors method is used, the new generation of the units will be: Select one: O a. P1, new = 65 MW, and P2, new = 155 MW O b. None of these C. P1, new = 68 MW, and P2, new O d. P1, new = 78 MW, and P2, new = 152 MW = 142 MW

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

3.n Figure 3P.2 shows two capacitor banks, C, and C2, in a substation C is enercized, but C, is discharged. The three-phase, 60 Hz ratings of the banks are: C,, 5 MVA; C,, 3 MVA, on a 13.8 kV base. The source has a short circuit rating of 20 kA rms at 13.8 kV. The inductance of the loop between C, and C,, represented by L, is 30 µH. 13.8 kV V3 L L2 o to C2 Source Capacitor banks ouG OL 19 Fig. 3P.2. Calculate the peak transient voltage that will appear on C, and the peak transient current that will flow in L,, if the switch S is closed at the peak of the voltage cycle. Point out any assumptions you make.
In a given system of base power of 250 MW, and bus 3 is taken as reference. The per-unit reactances are X₁2 = 0.2 p.u., X13 = X23 = 0.1 p.u. If the power flow in the system is given as: PF12 = 100 MW, PF13 = 50 MW, PF23 = -150 MW, then the phase angles are Select one: O a. 0₁ = 0.02 rad., 0₂ = 0.06 rad., 03 = 0 rad. O b. None of these O c. 8₁ = 0.02 rad., 02 = -0.06 rad., 03= 0.1 rad. O d. 0₁ = 0.02 rad., 02 = -0.06 rad., 03 = 0.2 rad. O e. 8₁ = 0.02 rad., 8₂ = -0.06 rad., 03 = 0.1 rad. O f. 0₁ = 0.02 rad., 02 = -0.06 rad., 03 = 0 rad.
The steady-state voltage drop between the load and the sending end of the line seen in (Figure 1) is excessive Suppose that V-4950/0° V (rms). A capacitor is placed in parallel with the 192 kVA load and is adjusted until the steady-state voltage at the sending end of the line has the same magnitude as the voltage at the load end, that is, 4950 V (rms). The 192 kVA load is operating at a power factor of 0.8 lag. Part A Calculate the size of the capacitor in microfarads if the circuit is operating at 60 Hz. In selecting the capacitance, use the value that results in the lowest possible power loss in the line. Express your answer in microfarads to three significant figures. ▸ View Available Hint(s) Figure 1 of 1 202 1100 192 kVA 0.8 lag ΜΕ ΑΣΦ. 11 vec C= 22.8 Submit Previous Answers Incorrect; Try Again; 5 attempts remaining Provide Feedback ? F
A generating station having two thermal generating units shown below with minimum and maximum generations of 45 MW,60 MW and 600 MW, 800 MW respectively, have the Gen-2 following cost equations. Gen-1 C, = 0.065 Pc1? + 25 Pc1 + 400 OMR / Hr C2 = 0.082 Pc2² + 8 Pc2 + 320 OMR / Hr Calculate the saving when they share load as per economic load dispatch compared to load sharing proportional to their maximum generation. Neglect line losses. 280 MW 400 MW
Explain the concept of load flow analysis in power systems. How does it help in determining the steady-state operating conditions of a power grid, and what are its limitations?
on DIS: (Answer these before coming to the experiment) Q1. Why sending end power is more than receiving end power in transmission? Explain Ref [1] reasons with necessary equations. Q2. For a give VR and I, the transmission line efficiency increases with the decrease in Ref [2] power factor for lagging loads. [True/False]? Q3. What is a peak load? How does it affect the power factor and Efficiency? Q4. The efficiency of DC transmission is more than AC transmission. Why? Q5. How Ferranti effect changes the transmission line efficiency? Explain. Ref [2] Ref [3] Ref [3]
A three phase, 50 Hz line has a resistance of 8 ohms and a reactance of l1l ohms. It supplies a 0.8 lagging pf load at a llkV. Find the load at which the source end voltage equals the load end voltage when a 25microfarad capacitor is connected across the load in each phase.
thats it
A system consists of four idenital 400 MVA generating units feed- ing a total load of 1016 MW. The intertia constant of each unit is 5 on 400 MVA base. The load changes by 1.5% for a 1% change in frequency. When there is sudden drop in load by 16 MW, obtain the power system time constant (T) with constants H and D expressed on 1600 MVA base.
Resistive load of 84.6 MVA is connected to a bus bar with 9.4kV. If the base of 100MVA and 10kV are selected, the load current (in per unit) is: a. 0.7 b. 1.0 C. 0.8 d. 0.9 e. 0.6