An interconnected cable link generating stations 1 and 2 is shown in figure.SG2SG1|V₂|26₁Sp1Bus-1X=j0.07 p.u.The total demands at the two buses are:Bus-2Sp2|V₂|200SD1 = (10+j5) p.u. and Sp2 = (20 +j18) p.u.The station loads are equalized by the flow of power in the cable. Generator G₁ can generate a maximum of 15 p.u. real power, sending end station power factor is_lagging.

An interconnected cable link generating stations 1 and 2 as shown- The total demands at the two…

An interconnected cable link generating stations 1 and 2 is shown in figure. SG2 SG1 |V₂|26₁ Spi Bus-1 X=j0.07 p.u. The total demands at the two buses are: Bus-2 Sp2 IV ₂140⁰ SD1 (10+j5) p.u. and Sp2 = (20 +j18) p.u. The station loads are equalized by the flow of power in the cable. Generator G₁ can generate a maximum of 15 p.u. real power, sending end station power factor is_ lagging.

An interconnected cable link generating stations 1 and 2 is shown in figure. SG2 SG1 |V₂|26₁ Spi Bus-1 X=j0.07 p.u. The total demands at the two buses are: Bus-2 Sp2 IV ₂140⁰ SD1 (10+j5) p.u. and Sp2 = (20 +j18) p.u. The station loads are equalized by the flow of power in the cable. Generator G₁ can generate a maximum of 15 p.u. real power, sending end station power factor is_ lagging.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Power
a question by considering the annual load time curve for an electric station as a straight line from 20mw to 3mw, and to cover these loads, then operate three generating units, the first and second, each with a capacity of 10mw, while the third has a capacity of 5mw, and illustrate the load time curve by drawing, then find: 1- the total capacity of the station 2- the maximum demand 3- capacitance coefficient 4- pregnancy coefficient 5 utilizatio
3.n Figure 3P.2 shows two capacitor banks, C, and C2, in a substation C is enercized, but C, is discharged. The three-phase, 60 Hz ratings of the banks are: C,, 5 MVA; C,, 3 MVA, on a 13.8 kV base. The source has a short circuit rating of 20 kA rms at 13.8 kV. The inductance of the loop between C, and C,, represented by L, is 30 µH. 13.8 kV V3 L L2 o to C2 Source Capacitor banks ouG OL 19 Fig. 3P.2. Calculate the peak transient voltage that will appear on C, and the peak transient current that will flow in L,, if the switch S is closed at the peak of the voltage cycle. Point out any assumptions you make.
A Single Area consists of 3 generating units (G1/G2/G3) with the following characteristics: G1: 200 MVA rating, R1 = 0.025 pu (on the 200 MVA base), initial output P1 = 150 MW. G2: 300 MVA rating, R2 = 0.01 pu (on the 300 MVA base), initial output P2 = 200 MW. G3: 400 MVA rating, R3 = 0.02 pu (on the 400 MVA base), initial output P3 = 300 MW. The frequency of the system is 60 Hz. Assuming D = 0.75 pu on a common base of 1000 MVA, what is the new generation output for G1 for a load increase of 150 MW? Select one: O a. None of these O b. 252.12 MW O c. 155.45 MW O d. 170.42 MW
A d.c. serier generator, having an external characteristic which is a straight line through zero to 50 V 200 A is connected as a booster between a station bus bar and a feeder of 0.3 ohm resistane. Calculate the voltage difference between the station bus-bar and the far end of the feeder qa current of (i) 200 A and (ii) 50 A.
Question 3 What is the value of real power supplied by the source in the figure? ww 30/0º V rms | C 40 3031.4 None of the answers 2007.8 5252.8
The steady-state voltage drop between the load and the sending end of the line seen in (Figure 1) is excessive Suppose that V-4950/0° V (rms). A capacitor is placed in parallel with the 192 kVA load and is adjusted until the steady-state voltage at the sending end of the line has the same magnitude as the voltage at the load end, that is, 4950 V (rms). The 192 kVA load is operating at a power factor of 0.8 lag. Part A Calculate the size of the capacitor in microfarads if the circuit is operating at 60 Hz. In selecting the capacitance, use the value that results in the lowest possible power loss in the line. Express your answer in microfarads to three significant figures. ▸ View Available Hint(s) Figure 1 of 1 202 1100 192 kVA 0.8 lag ΜΕ ΑΣΦ. 11 vec C= 22.8 Submit Previous Answers Incorrect; Try Again; 5 attempts remaining Provide Feedback ? F
Q)The question is that how kW is converted to kVA in complex form and how kV square is 2.4 for T1,T2,T3 can you plz explain it by seeing the solution
A Load of particular kVA is drawing a current which lags behind the voltage at an angle of 63.43 degrees. The operating power factor is __________ . a. 0.5958 b. 0.6122 c. 0.6511 d. 0.4472
Subject is Power system analysis
Q3. For the circuit shown below, sketch the current waveforms iş and io and determine the Average and RMS for both currents. i, 1:1 ɑi = 15° Vs = 220 V az = 250° ot i. 302 VR ot 2n
Q1. In which of the following cases, the Electrostatic Discharge (ESD) is more? Explain how the ESD event taken place in both the cases. a. A person walking across a synthetic carpet on a dry day and generates a potential of 15 kV on his body. b. A person walking across a plain ground surface on a dry day and generates a potential of 100 V on his body.