Given a 76sqm residential unit to be provided with 230V, single phase power supply with the ff appliances: 1Hp ACU for each bedroom 1.5Hp ACU in the living-dining area 800W Water heater in the bathroom 2000W Microwave Oven 3500W Washing Machine 1. Compute for the total demand load in VA 2. Specify the rating of branch circuit and size of wire, circuit breaker for lighting, convenience (small appliance) outlets, aircon, water heater, micro oven and washing machine 3. Compute and specify the size of the feeder using TW wire and the main circuit breaker. Ⓒ XI Co MASTER BEDROOM KITCHEN AREA BALCONY BEDROOM 2 LIVING ARCA DINING AREA Ⓒ

Given a 76sqm residential unit to be provided with 230V, single phase power supply with the ff appliances: 1Hp ACU for each bedroom 1.5Hp ACU in the living-dining area 800W Water heater in the bathroom 2000W Microwave Oven 3500W Washing Machine 1. Compute for the total demand load in VA 2. Specify the rating of branch circuit and size of wire, circuit breaker for lighting, convenience (small appliance) outlets, aircon, water heater, micro oven and washing machine 3. Compute and specify the size of the feeder using TW wire and the main circuit breaker. Ⓒ XI Co MASTER BEDROOM KITCHEN AREA BALCONY BEDROOM 2 LIVING ARCA DINING AREA Ⓒ

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

2. A series circuit consisting of a 0.0795-henry inductor and a 177-microFarad capacitor is connected to a 120-volt 60-cycle source. Calculate (a) the equivalent reactance of the circuit. (b) the circuit current. indicaling Whether the latter lags or leads
5
17. Which of the following measurements should be recorded in installation documentation?A. Multimeter measurementsB. OTDR measurements onlyC. Power meter measurements onlyD. All power meter and OTDR measurements
We have a 240/120V single-phase three-wire feeder circuit that powers the following loads: a 5 hp, 230V single-phase motor; a load of outlets in discontinuous operation, distributed in 37.5 A for each ungrounded conductor; a load of devices working continuously and distributed in 30 A for each ungrounded conductor; a lighting circuit that works continuously and distributed in 40 A for each conductor not grounded; a heating load of 10 kW at 240 V; a 1 hp 120V single phase motor and a 2 hp 120V single phase motor. Size the feeder conductors and the main OCPD.Size the grounded conductor
Outline the important elements of a solar power supply for a small office or large home. Explain how energy demands and parameters are determined. Present safety concerns and how they can be mitigated. Reference is to be made to system sizing, Grid Tied arrangements, off-grid benefits/ drawbacks.
A 4-bus three-phase power system consists of the following equipment: • Generator 1 connected to bus 1 with a rated power of 20MVA, rated voltage of 20 kV, and a series reactance of 0.4 p.u. • Generator 2 connected to bus 5, with a rated power of 12MVA, rated voltage of 10 kV, and a series reactance of 0.3 p.u. Transformer 1 connected between buses 1 and 2, is wye-wye connected with a rated power of 20 MVA, rated voltages 20/100 kV, and a series reactance of 0.1 p.u. • Transformer 2 connected between buses 4 and 5, is wye-wye connected with a rated power of 12 MVA, rated voltages 12/110 kV, and a series reactance of 0.15 p.u. • Transmission Line 2-3 connects buses 2 and 3 and had a series impedance of 50 + j75 ohms. • Transmission Line 3-4 connects buses 3 and 4 and had a series impedance of 40 + j80 ohms. • Load A connected to bus 3 and abosorbes20 MW and 10 MVAR. The voltage at bus 3 is 105 kV. 1) Draw the one-line diagram for the system. 2) Draw the per-unit, per phase…
I need answer fast please
1. What is the ultimate objective of an interconnection? 2. What does it mean when the ACE of all areas in an interconnection is equal to ZERO? 3. Explain the difference between the ACE in a single-area power system and the ACE in two-area power system. 4. If there is a decrease in frequency of a two areas interconnection, but the net interchange power leaving balancing area 1 increases. This means: 5. If the monitoring system indicates a negative ACE, what does this means? 6. Briefly discuss the term Frequency Response. 2 2-1 LilAJ 11:06 PM 8/29/2021 A ENG
polyphase please answer as soon as possible
A 3_phase, 10 MVA/11KV Y connected, alterneter is protected by merz_ price circulating current system. The star point is earthed throug at risistance of 5 ohm. If CTs have rations of 1000/5 and The Realy is set to operate when their is overload with 30%. Determine 1) Determine The Percentage of each phase of stator winding which is protected if the reactance of the stator winding is 10% Per phase 2) Determine The minimum value of earthing risistine to Protect 85% of the winding negleet of The reactance of the stator winding in this case
I need the answer at 20 minute .
Problem-2 • A star-connected, 3-phase, 10 MVA, 6.6 kV alternator is protected by a differential current protection scheme using 1000/5 A current transformer. The star point of the alternator is earthed through a resistance of 7.5 Q. If the minimum operating current for the relay is 0.5 A, Calculate the(% of each phase of the stator winding which is unprotected against earth- fault when the machine is operating at normal voltage.