Gazprom company in Russia required to compress the gas by using a single stage compressor to compress 18 MMscfd of a 0.5 gravity gas from 100 psia and 150°F to 600 psia according to the polytropic equation. Calculate the horsepower, speed of compressor and efficiency? Tsc = 60°F, Z₁=0.43, Other data are: K=1.4 Psc = 14.7, Z2-0.44, Bg-0.160 ft³/scf

Gazprom company in Russia required to compress the gas by using a single stage compressor to compress 18 MMscfd of a 0.5 gravity gas from 100 psia and 150°F to 600 psia according to the polytropic equation. Calculate the horsepower, speed of compressor and efficiency? Tsc = 60°F, Z₁=0.43, Other data are: K=1.4 Psc = 14.7, Z2-0.44, Bg-0.160 ft³/scf

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Air (R = 0.3074 psia.cf/lbm.R) is compressed from 14.7 psia and 60°F to a pressure of 150 psia while heat loss rate during the steady compression is 10 Btu/lbm. The volume flow rate of the air at the inlet is 5,000 ft'/min and the power input to the compressor is 700 hp. Determine the temperature at the compressor exit in °F. (1hp = 0.7068 Btu/s) AIR %3D 10 Bru Ibm
CO2 is needed in a surgical suite for abdominal laparoscopic surgery. You have already designed a nozzle to step down the pressure from the gas cylinder to the delivery hose. The well-insulated delivery hose has a 2.2 mm inner diameter. The inlet conditions to the delivery hose are 103 psia and 17°C. Typically, the surgeon uses 4 to 6 L/min of gas at pressures between 10 to 20 mm Hg to inflate the peritoneal cavity; however, the delivery system must be able to provide flow rate of 17.5 L/min at 20.0 mm Hg for safety. The surgeon will use a pin valve to control the flow rate and maintain the operating space. The gas temperature should not be any colder than 10°C when delivered to patient, or tissue damage might occur. Determine the acceptable delivery hose length to meet the surgical criteria. State assumptions.
3- Air compressor compresses (7.8m/min) of air at (27°C) and (100kPa) to (925kPa). Determine the power required when the compression:(a) isothermal, (b) polytropic according to PV2–C. find the averall efficiency if the mechanical efficiency is (90%).
Q6/ A single compressor system using 134a has a three evaporators of 5, 15 and 20 tons capacities. All evaporators operating at the same temperature of 0 °C. The condenser pressure is 12 bar and the refrigerant exit of the condenser as a sub cool at 40 °C. The discharge from the evaporator is dry saturated vapour *: and the compression is assumed to be isentropic. The cop is
A single-stage double-acting air compressor compresses the air from 1 bar to 5 bar. The compressor runs at 2.2 rps and work done during the compression is 36 kJ. Calculate the power required in kW. the power required in kW
45 lll a O L O A:EV 1 aj3vkuusfe Example: The maximum temperature in a diesel engine is 2700K with a compression ratio of 30. The initial state of the compression process is 30C and 100 kPa. Find 1- The amount of the input heat transfer 2- The amount of the output heat transfer 3- The amount of the net work done 4-The thermal efficiency 5-The mean effective pressure تم انضمام أمجد شاكر والي حميد إلى الاجتماع. ۱۳ مشارك آ. . . غزوان احمد عمار حسن esi ...
Considering air standard values, calculate for the net work in BTU/min given that the suction of the compressor is 0.04M cfm at 0.3 psig & 550R; rk = 10/2 and the temperature at the entrance of the turbine is 1864R; pressure at the exit of the turbine is 15 psia.
Steam at 1 kg / s mass flow enters a steam isentropic turbine at a pressure of 4 MPa, a temperature of 300ºC and a speed of 50 m / s, and leaves it at a pressure of 150 kPa and a speed of 200 m / s. .Note: T0 = 25 ºC, P0 = 100 kPa, T (K) = 273 + ºC a) Find the power produced by the turbine.b) Find the reversible power produced by the turbine.c) Find the isentropic efficiency of the turbinec) Find the second law efficiency of the turbine.
Air is used as a working substance in a given internal combustion engine, which is supplied with heat at a constant volume. Based on the data, calculate the Pressure and temperature of the ending of isentropic expansion.