FS 2.875 m 4.252 m 5.478 m 6.142 m BS ТР 1 ТР 2 4.325 m 9.542 m 9.631 m 8.133 m BM 1 Elev. = 56.287 m ТР 3 Not to scale BM 2 Given the traverse illustration above, fill up and complete the table below. Make sure to show your solution in solving for HI, Elevation, Correction to be applied, and Corrected Elevation. BS HI FS Elevation Corrected Station (m) (m) (m) (m) Elevation (m) BM1 ТР BM2 TP3 ТР BM1 7.258 m 2.841 m

FS 2.875 m 4.252 m 5.478 m 6.142 m BS ТР 1 ТР 2 4.325 m 9.542 m 9.631 m 8.133 m BM 1 Elev. = 56.287 m ТР 3 Not to scale BM 2 Given the traverse illustration above, fill up and complete the table below. Make sure to show your solution in solving for HI, Elevation, Correction to be applied, and Corrected Elevation. BS HI FS Elevation Corrected Station (m) (m) (m) (m) Elevation (m) BM1 ТР BM2 TP3 ТР BM1 7.258 m 2.841 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine Slope at A, B, D (Indicate direction) and displacemnet of point A (Indicate direction) Tabulate final answer as Value Direction Slope at A Slope at B Slope at D Displacement at A
a. Two points A and B (distance =100m) were nominated at the field and Two points A and B (distance =100m) were nominated at the field and At Mid Point At End Point Point A 1.477 1.626 Point B 1.055 1.201 Height Diffierence Calculate the collimation error and demonstrate with a figure. Comment on the vertical collimation error and explain how we can adjust the vertical collimation error for a levelling instrument?
In the figure, what is the slope of member EM ? 3 KN 2 KN 6 KN 8 KN 6 KN 2 KN 3 KN 0.50 m J 6 @ 1 m-6m K T. XX O 1:2 O 2:1 O 2:3 О 1:3
Using double integration method, determine the value of the constant, C, for segment AB. M=400 kN.m |50 kN -6m- 1100 kN -6m- A B.
Find the discharge of rectangular orifice 3.0 m wide and 2 m deep fitted to a water tank. The water level in the tank is 4 m above the edge of the orifice. Take C=d0.62. (Note: Include FBB of the problem if needed.) Choices:a.36.77 m^3/s b.23/68 m^3/s c.45.34 m^3/s d.56.32 m^3/s
Using virtual work, determine displacement at B. (E = 29,000 ksi & I = 1,000 in^4)
Read the question carefully and give me both right solutions.
Just Find Depth and width that gives the given I .
A built-up beam made from fastening two channels to a wide flange section carries loads as shown. The fasteners are 12mmØ bolts with allowable shear stress t = 110 MPa. For bearing op= 220 MPa for single shear, and op= 275 MPa for double shear. E= 200 GPa. Fy= 420 MPa a. Determine the horizontal shearing stress at 20 mm above the Neutral Axis b. Determine the horizontal shearing stress at 95 mm above the Neutral Axis
8. RISB AND FALL camplete the level notes given: below and show the customary arithmetic check. METHOD. Using the rise and fall method, ROD READINGS IFS DIFFERENCE IN ELEV RISE REDUCED LEVEL STA BS FS FALL 1.73 766.45 m BM13 O+00 2.05 +35 1.88 +60 1.75 + B0 I +00 2.39 3.25 +15 2.44 +40 1.86 +90 1.09 2+00 2.15 TP- 1.84 2.63 2+45 О.77 +68 3+00 1.19 1.08 +50 2.52 BM 14 2.J4
Determine the moment of inertia (cm4)of the cross section shown with respect to the horizontal centroidal axis if a=15cm, b=36cm, c=22cm, r=2cm, s=2cm, and t=2cm. Round off only on the final answer expressed in whole number.
I want an accurate and detailed solution