4. RISB AND FALL complete the level notes given: below and show the customary arithmetic check. METHOD. Using the rise and fall method, ROD READINGS IFS DIFFERENCE IN ELEV RISE REDUCED LEVEL STA BS FS FALL BM13 O+00 1.73 766.45m 2.05 +35 1.88 +60 1.75 +B0 2.39 00+1 +15 3.25 2.44 +40 1.86 +90 1.09 2+00 2.15 TP-I 1.84 2.63 2+45 0.77 +68 1.19 3+00 1,08 +50 2.52 BM 14 2.J4

4. RISB AND FALL complete the level notes given: below and show the customary arithmetic check. METHOD. Using the rise and fall method, ROD READINGS IFS DIFFERENCE IN ELEV RISE REDUCED LEVEL STA BS FS FALL BM13 O+00 1.73 766.45m 2.05 +35 1.88 +60 1.75 +B0 2.39 00+1 +15 3.25 2.44 +40 1.86 +90 1.09 2+00 2.15 TP-I 1.84 2.63 2+45 0.77 +68 1.19 3+00 1,08 +50 2.52 BM 14 2.J4

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

See example below. Change data but solve method of 11.
Choose the right answer with solution thank you! I need asap after twenty minutes thank you.
Solve the following problems completely and neatly. Use 3 decimal places in all your computations except for strain and rho(5 decimal places). Input your answer in the text box provided in each number. Calculate the depth of the neutral axis of the section in PART B in mm.0
Solve the following problems completely using Double Integration Method, Area moment method and Conjugate beam method for each problem. Round off your answers to 3 decimal places. Problem 1 w а. RA b. MA A B C. RB L Problem 2 10 kN/m a. Location of Amax from A b. Amax A В 10 m.
Q1/Find the horizontal displacement at C . and @y by using Virtual Work Method, i you know E - 200 GPa, I - 25°(10% mmé , (P KN)
Figure Q3 shows an overhead crane truss supported by pin and roller supports at point A and E. The truss is subjected to forces of 20 kN, 30kN and 20 KN acted at joint G, H and I, respectively. The cross-section area for the truss member is 2000 mm? and the Young's Modulus for all truss members is 250 kN/mm?. As a structural engineer, you are responsible to ensure the overhead crane truss is safe during maintenance works. Therefore, the crane is additionally supported by roller support at joint C. Calculate reaction, R. at support C (assume the unit load acting downward)? (a) (b) How do you present the new data on internal force for member BC when overhead crane has additional roller support at Joint C?
show solutions b) Spacing of stirrups at 1.0m from fos.
Please help ASAP Give typed answer I will upvote and good Feedback
| Calculate the slopes "8." and "8" in the frame shown in figure using "Slope-Delection Equations". Do not solve the system. Do not draw any diagram. (E: Constant). ("A" is the fixed type of support and "C" is the pin). 20 Nim 20 KNim D () B 30 kN (1)
Derive the following Equation of maximum Deflection using double integration method.
Q2: Use the Vector Polygon Method to calculate the resultant and its direction of the four coplanar forces below: Note that 1 kilo Newton - 224.8 pounds Or. 1 kN-224.8 lb. 10 kN 1124 ib يجب أن يحل هذا السؤال على ورق بياني( 8 kN+ 45 34 7 kN
An engineer used a 30 m tape in measuring an inclined ground 459.20 m long. The difference between the starting point and end point is 1.20 m. The tape is of standard length at a temperature of 100 C and a pull of 50 N. During measurement the temperature reading was 15 0 C and a pull of 75N applied at both ends. A= 6.5mm2 ; E = 200GPa; K = 0.0000116 m/C0 . The mass of the tape is 0.075kg/m. Determine the horizontal distance.