Calculate the depth of the neutral axis of the section in PART B in mm.0

Q: Use Virtual Work Method to answer the questions below considering the truss shown. Use the…

A: Note: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question…

Q: Given the figure, find the tension at A, B, C, D in Newton. The other photo is the continuation of…

A:

Q: Problem 1 Consider a problem of plane stress. It is given that σ = 2a, and that σ₂ = 3a and Os = a…

A:

Q: Determine the force in each member of the Truss shown in the figure and indicate whether the members…

A:

Q: a b

A:

Q: The answer is -4.58 in. (displacement of point B) just show the solution.

A:

Q: For the truss shown in Figure 3, members AC and BC have cross sectional area of 2 in.² while members…

A:

Q: In the figure, one end of a uniform beam of weight 270Nis hinged to a wall; the other end is…

A:

Q: Break it down first and then solve for AB once u solve it, u solve for BC.   Take w=789

A:

Q: Determine the moment of inertia about the x-axis of the rectangular area without and with the…

A:

Q: stresses in each element. E=30E6 psi, Elemer ment 3 has Area = 20 in?, Use both software an 6 ft 2

A:

Q: w=24kn/m a = 15m I = 70 x 10^6 mm^4 E = 200 GPa Find displacement at C using moment area method

A: Given Data  E = 200 GPa = 200 × 103 N/mm2  I = 70 × 106 mm4  Determine the displacement…

Q: Balancing the sums of the forces in the primed coordinate system yields two equations: 0x = 0x cos²…

A: Step 1: Step 2: Step 3: Step 4:

Q: 78. Determine the midspen yalue of EI8 for the beam shown in Fig. P-678. EI8 = 2810N m Ans. 600 N…

A: The beam with two concentrated load is applied on it at a distance 3m and 4m from R1, we need to…

Q: 14 kips. Consider only flexural deformations. | A B 7'-

A:

Q: 25 mm 200 mm V 100 mm 25 mm 25 mm 25 mm 200 mm 25 mm

A:

Q: Consider the deformable pin-jointed truss with loading, geometry and section properties as shown in…

A:

Q: Consider the truss shown in (Figure 1). Take A = 0.0015 m² and E = 200 GPa for each member, and F=…

A:

Q: Draw the diagram of normal forces, stresses and displacements along the length of the stepped bar…

A:

Q: The cross sectional area of each member of the truss shown in the figure is A = 500 mm^2 and E = 200…

A:

Q: Determine the force in each member of the loaded truss. The force is positive if in tension,…

A:

Q: 5.15 A beam in bending has the cross section of an L3 × 2 × 0.25 in unequal leg steel angle. A…

A:

Q: A wooden beam is loaded by a distributed load w = 6 N/mm as shown in Figure Q4(a). The cross-section…

A:

Q: A rod of homogeneous thickness shown in the figure is AB length L and BC length 2L. Find the angle…

A:

Q: For the shape below determine the centroid relative to the x and y given. Once you have the centroid…

A: Given:b=4, h=4 and r =0.2Required:Centroid locationMoment of inertia about an axis through centre…

Q: For the structure in this figure , write an expression that would determine the horizontal…

A:

Q: A rectangular bar is subjected to tensile forces of 2230 kN. Use E = 110 GPa and v= 0.34. Determine…

A:

Q: calculate the centroid and moment of inertia

A: The given cross-section is divided into 2 rectangles and 3 triangles as shown below The areas…

Q: PROBLEM 2 A steel bar is bolted to another solid steel structure as shown in Figure 2. A force 400…

A: Introduction- Reinforcing bars, or rebars, are another name for steel bars. It's a steel wire mesh…

Q: Find 1. BMD of real beam 2. Conjugate beam+ loading 3. Reactions of conjugate beam

A: P1 = 80KN P2 = 40KN [Note : As per rule I have solved first 3 part, post other part separately]

Q: Fourier series: simply supported beam deflection under trapezoidal load

A:

Q: 6...

A: If you have further doubts about this. I will be happy to help you solving this. Thank you!

Q: Determine the orientation of principal planes of stress. Enter your answers in degrees to three…

A:

Q: Consider the rod shown. Suppose that hℎ = 170 mm, r = 290 mm. Determine the location (x,y)  of the…

A: The Centroid is the center of mass of the section of beam. It is considered as the center point of…

Q: 4. Complete the following a. Draw Mohr's circle for the element given and label the axes b.…

A: Answer  Since we are not allowed to provide handwritten solution we have used Autocad to draw the…

Q: A В C D' | 280 kip.ft 10ft 10ft 10ft tf y |1/4 d В d d x- y -by-

A: The given data is shown below: σx=-10 ksiζxy=-3 ksi

Q: For the structure and loading shown below, find the lateral deflection at the top. Use E = 29,000…

A:

Q: 1.5 m B -1 m z 2 kN A

A:

Q: 5 mm 400 mm- |A B. 3 mm 300 mm C

A:

Q: Determine:a) the horizontal displacement of joint A of the steel truss. b) Due to fabrication error,…

A: Step 1:Step 2:Step 3:Step 4:

Q: In figure shown the cross-sectional area of BD and CE is 2 mm?, E = 210 GPa, L, = 350 mm, L2 = 200…

A:

Q: THE INTERNAL FORCE OF MEN mpression, include a negative sign two (2) decimal places only witho…

A:

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.