Forces in the column bars are transferred to the footing through No 10 bars. Determine the development length required into the column and into the footing if the steel has a yield stress of 60 ksi. Normal weight concrete is used. The concrete strength in the column is 6,000 psi and the concrete strength in the footing is 5,000 psi up into column down into footing

Forces in the column bars are transferred to the footing through No 10 bars. Determine the development length required into the column and into the footing if the steel has a yield stress of 60 ksi. Normal weight concrete is used. The concrete strength in the column is 6,000 psi and the concrete strength in the footing is 5,000 psi up into column down into footing

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A rectangular concrete beam has a width of 300mm and an effective depth of 550mm. The cantilever beam is loaded as shown. Assume f = 21 MPa and fy = 312 MPa. Compression reinforcement if necessary shall be placed at a depth 80mm from the outermost compression concrete. Determine the required number of 25mm tension bars. Draw the details of the rectangular beam. 20 kN/m 3 m 2 m 2 m 40 kN
Question 33 A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yield strength fy = 350 MPa for 20-mm bars and fy = 275 MPa for 16-mm bars. Determine the maximum steel ratio if the beam is singly reinforced in negative bending with the given material strengths and the tensile strain is limited to 0.004 upon crushing of concrete. Write the answer in 5 decimal places only.
Design Problem 1 & 2 Determine the cracking moment for the prestressed beam section shown if f'c = 35 MPa. Use a modular rupture of fr Assume normal weight concrete. = 0.621√ f'c C = 100 mm b₁ = 350 mm D = 125 mm d = 440 mm h = 500mm b₂ = 200 mm Figure 1.0 Cc 60 mm C-150 mm h, 250 mm b₁ = 250 mm b. =350 mm Figure 2.0 d 630 mm h = 700mm Ce 70 mm
Top tie 4. Assume that the wet concrete (s.w. = 150 Ibf/ft3) behaves as a liquid. Determine the force per unit foot of length exerted on the forms. If the forms are held in place as shown, with the ties between vertical braces spaced every 2 ft, what force is exerted on the bottom tie? Brace Form 9 ft Concrete Bottom tie
Determine the additional longitudinal reinforcements (mm2) due to torsion of a rectangular beam with a width of 469 mm and an over-all depth of 632 mm. It is subjected to a factored torsion of 110 kN-m. The specified compressive strength of concrete is 21.70 MPa. The yield strength of tension reinforcements and stirrups are 348 MPa and 278 MPa respectively. Use 12 mm stirrups. Round off only on your final answer (3 decimal places).
A prestressec concrete beam 300 mm wide and 600 mm deep is prestressed using 5 high tension bors f 12 mm o provide at 220 mm from the soffit of the beam. The effective stress in the steel is 800 N/ m Find the bending that niust be applied to the section to just auoid tension at the soffit of the beam.
Question 31 A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yield strength fy = 350 MPa for 20-mm bars and fy = 230 MPa for 16-mm bars. Determine the design moment capacity in kN∙m of the beam in negative bending. Write the answer in 2 decimal places only.
just answer d to f
Pre-stressed.
The maximum compression in a concrete beam fiber is 6.2 MPa. The depth of the neutral axis is 124 mm and the characteristic compressive strength of the concrete is 25 N/mm?. Determine the effective curvature of the beam,
PLEASE SOLVE AND BOX ALL FINAL A LITTLE CONFUSED
Correct solution