einforced concrete beam has a width of 325 mm. and a total depth of 450 mm. It has an effective depth of 375 mm and is reinforced with steel reinforcement having a total steel area of 1875 sq.mm. in one layer fc’ = 27.6 MPa and fy = 414.7 MPa. a. Determine the depth of the compression block

einforced concrete beam has a width of 325 mm. and a total depth of 450 mm. It has an effective depth of 375 mm and is reinforced with steel reinforcement having a total steel area of 1875 sq.mm. in one layer fc’ = 27.6 MPa and fy = 414.7 MPa. a. Determine the depth of the compression block

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Concrete beam.
Question 5 A rectangular presressed concrete beam of span 15 m and width 500 mm is loaded with a live load of 30 kN/m. The prestressing force is KN. [Take permissible stresses in concrete and steel as 15 MPa and 1200 MPa respectively]
A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. The concrete cover to bar centroid is 80 mm and at the bottom is 70 mm. use concrete strength f'= 21 MPa and steel yield strength fy=415 MPa for all bars. 1. Determine the tensile steel ratio when the beam is in positive bending. a. 0.01567 b. 0.01283 c. 0.01169 d. 0.01923 2. Determine the nominal moment capacity in kN-m of the beam in positive bending. a. 188.30 b.167.70 c.218.96 d.193.68 3. Determine the tensile steel ratio when the beam is in negative bending. a. 0.00406 b. 0.00475 c.0.00383 d. 0.00508 please provide a complete solution so I can understand. Very much appreciated to solve it early !!
RCC.
Use f'c = 30 MPa and fy = 415 MPa. The unit weight of concrete is 24 kN/m³ . The floor of a cantilever floor system is made up of a 150mm thick concrete slab (cast monolithically with beam) and the beams have widths of 300 mm, a total depth of 560 mm, and are to be reinforced with 5-Ø28 mm bars. The center-to-center spacing of beams is 4 m. The cantilever floor system is also built using 4m cantilever reinforced beams as supports. a) Find the maximum service live load (kPa) that the current floor design can support. b) Suppose that the floor will need to carry a superimposed service dead load of 2 kPa and service live load of 7.2 kPa, will the existing floor design be adequate? If not, redesign the beams (find the appropriate number of Ø28-mm rebars and provide a final sketch). Use cc = 40 mm, stirrup diameter of 10 mm, and nominal maximum aggregate size of 20 mm.
Problem #1. The base of a rectangular reinforced concrete beam is 300mm and the effective depth is 550mm. Concrete compressive strength on the 28" day is 24MPA and steel yield strength is 415MP.. Determine : a. The depth of compression block (in mm, 2 decimal places), the strain in the tension steel (5 decimal places) and ultimate moment capacity (in KN.m, nearest tenth) of the beam if it is reinforced with 4-32mm diameter bars. b. The depth of compression block, the strain in the tension steel and ultimate moment capacity of the beam if it is reinforced with 4-20mm diameter bars.
A prestressec concrete beam 300 mm wide and 600 mm deep is prestressed using 5 high tension bors f 12 mm o provide at 220 mm from the soffit of the beam. The effective stress in the steel is 800 N/ m Find the bending that niust be applied to the section to just auoid tension at the soffit of the beam.
just answer d to f
Pre-stressed.
Determine the service level moment capacity. The allowable stress for concrete is , and the allowable stress for steel is 30000 psi.
A 6m long simply supported reinforced concrete beam has a width of 350mm and an overal1 depth of 470mm. The beans is reinforced with 2-28mm compression bars and 4-28mm tension bars, each located 70mm from the extreme fibers. Concrete strength f'c = 20. 7 MPa, and steel yield strength fy=415 MPa. Determine the ff: 1) Depth of compression block assuming both tension and compression steel yields. 2) what is the ultimate moment capacity of the beam in KN.m. 3) Determine the additional concentrated live load that can be applied at midspan if the dead load including the weight of the beam is 20KN/m. Use Mu=1.2Mdl+1.6M11 (Based of NSCP 2015) Show complete solution and neat handwriting. Use NSCP 2015.
The maximum compression in a concrete beam fiber is 6.2 MPa. The depth of the neutral axis is 124 mm and the characteristic compressive strength of the concrete is 25 N/mm?. Determine the effective curvature of the beam,