Calculate the top and bottom stress at transfer stage and service stage. Consider three 0.6" Grade 270 seven wire strands. 500 mm 200 mm 500 mm 400 mm 300 mm Details: f'c (at release) = 27.5 Mpa f'c = 41.4 Mpa 0.6" Grade 270 seven wire-strand fej = 1364.5 MPa (initial) fer = 1294 MPa (final) Maw = 76.15 kN-m MSDL = 25 kN-m ML = 83.04 kN-m %3D %3D %3D %3D

Calculate the top and bottom stress at transfer stage and service stage. Consider three 0.6" Grade 270 seven wire strands. 500 mm 200 mm 500 mm 400 mm 300 mm Details: f'c (at release) = 27.5 Mpa f'c = 41.4 Mpa 0.6" Grade 270 seven wire-strand fej = 1364.5 MPa (initial) fer = 1294 MPa (final) Maw = 76.15 kN-m MSDL = 25 kN-m ML = 83.04 kN-m %3D %3D %3D %3D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

STRENGTH OF MATERIALS (SIMPLE STRAIN:Poisson’s Ratio: Biaxial and Triaxial Deformations)100% UPVOTE! PLEASE INCLUDE FBD IF NECESSARY. THANK YOU! GOD BLESS!
The column above is subjected to axial loading only. Assume the following: • E= 29000 ksi G = 10000 ksi • = 986 in4 A = 60 in? • L= 20 ft • Grade 60 steel (60 ksi yield stress) • The column is fixed at the top and pinned at the bottom Which of the following is closest to the maximum normal stress the column can support (before yielding or buckling)? 167 ksi 24 ksi 42 ksi 60 ksi
Q/ Find the Maximum stresses in Steel and Aluminum. Est= 210G pa and E al%3D 70 G pa ? W= 15 Kn.M 120mm 5m Al steel 60mm 140 mm
PLEASe answer this question. Thank you
Please show a detailed solution and explanation including its FBD. Thank you!
A 1.65m long rod with a circular cross-section is subjected to a tensile load of 50 kN. The rod is made from AISI 1040 hot-rolled steel. The allowable tensile stress is 165 MPa. The rod is permitted to elongate up to 7mm without causing any issues. The proportional limit for the steel is 180 MPa. (A) Compute the required area necessary to meet the stated requirements based on allowable stress. Express your answer in square millimeter units as an integer. (B) Compute the required area necessary to meet the stated requirements based on allowable elongation. Express your answer in square millimeter units as an integer.
Round off final ans only, dont round initial values
Required information Consider the loading shown. The allowable normal stress for the steel used is 160 MPa. 0.8 m 50 kN/m B -2.4 m- 0.8 m For the selected design, determine the actual value of Om in the beam. (Round the final answer to one decimal place. You must provide an answer before moving to the next part.) The actual value of om in the beam is 160 MPa.
What is the manufacturing tensional yield strength (lbf) of grade S135 drill pipe? a. This is a trick question because drill pipe size is not provided b. The answer can’t be calculated because the length of the pipe is not given c. The yield strength is 135000 psi and is a property of the steel d. The yield strength is 135000 psi and depends on the cross-sectional area
PLEASE ANSWER THIS QUESTION ASAP!!!
Determine the safe load of the column section shown, if it has a yield strength of 25 MPa. E = 200000 MPa. Use NSCP Specifications. Fyz248 mpa Properties of Channel Section d = 305 mm t₂ = 7.2 mm A = 3929 mm² t₁ = 12.7 mm Ix=53.7 x 10mm¹ x = 117 mm Properties of W 460 x 74 A = 9450 mm² b = 190 mm ly= 1.61 x 10 mm x = 17.7 mm tw = 9.0 mm rx = 188 mm ry = 41.9 mm d = 457 mm tr = 14.5 mm Ix = 333 x 10 mm Iy = 16.6 x 10mm* 7.21 When the height of column is 6 m. When the height of column is 10 m. Assume K= 1.0 457 CIVIL ENGINEERING- STEEL DESIGN
42 KN the cross-sectional area of each member is 600 mm² Determine the stress in member EF. Answer in MPa rounded-off to 2 decimal places AddSNUIF ana. 2m A Last saved 4:09:09 PM 1455 ET 2 m Next > Last >