For two infinite slopes (one in dry condition and other in submerged condition) in a sand deposit having the angle of shearing resistance 30°, factor of safety was determined as 1.5 (for both slopes). The slope angles would have been..

For two infinite slopes (one in dry condition and other in submerged condition) in a sand deposit having the angle of shearing resistance 30°, factor of safety was determined as 1.5 (for both slopes). The slope angles would have been..

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter12: Subsurface Exploration

Section: Chapter Questions

Problem 12.11P

See similar textbooks

Similar questions

Refer to Problem 6.1. Using Eqs. (6.3) and (6.29), estimate the average stress increase (Δσav) below the center of the loaded area between depths of 3 m and 6 m. 6.1 A flexible circular area is subjected to a uniformly distributed load of 150kN/m2 (Figure 6.2). The diameter of the load area is 2 m. Determine the stress increase in a soil mass at points located 3 m below the loaded area at r = 0. 0.4 m, 0.8 m, and 1 m. Use Boussinesq’s solution. Figure 6.2 Increase in pressure under a uniformly loaded flexible circular area
Refer to Problem 17.7 and Figure 17.16. Suppose a footing (1.5 m 1.5 m) is constructed at a depth of 1 m. a. Estimate the design values for N60 and . b. What is the net allowable load that the footing can carry? The maximum allowable 17.7 settlement is 25 mm. Use Eqs. (16.56) and (16.61). Refer to the boring log shown in Figure 17.16. Estimate the average drained friction angle, , using the Kulhawy and Mayne correlation [Eq. (17.24)]. Assume pa 100 kN/m2. Figure 17.16
Redo Problem 6.12 using Figure 6.15. 6.12 Refer to Problem 6.1. Using Eqs. (6.3) and (6.29), estimate the average stress increase (av) below the center of the loaded area between depths of 3 m and 6 m. 6.1 A flexible circular area is subjected to a uniformly distributed load of 150 kN/m2 (Figure 6.2). The diameter of the load area is 2 m. Determine the stress increase in a soil mass at points located 3 m below the loaded area at r = 0, 0.4 m, 0.8 m, and 1 m. Use Boussinesqs solution. Figure 6.2 Increase in pressure under a uniformly loaded flexible circular area
The soil profile at a site consists of 10 m of gravelly sand underlain by a soft clay layer. The water table lies 1 m below the ground level. The moist and saturated unit weights of the gravelly sand are 17.0 kN/m3 and 20.0 kN/m3, respectively. Due to some ongoing construction work, it is proposed to lower the water table to 3 m below the ground level. What will be the change in the effective stress on top of the soft clay layer?
The soil profile at a site consists of 10 m of gravelly sand underlain by a soft clay layer. The water table lies 1 m below the ground level. The moist and saturated unit weights of the gravelly sand are 17.0 kN/m3 and 20.0 kN/m3, respectively. Due to some ongoing construction work, it is proposed to lower the water table to 3 m below the ground level. What will be the change in the effective stress on top of the soft clay layer?
A shallow square foundation for a column is to be constructed. It must carry a net vertical load of 1000 kN. The soil supporting the foundation is sand. The standard penetration numbers (N60) obtained from field exploration are as follows: FIG. 17.15 The groundwater table is located at a depth of 12 m. The unit weight of soil above the water table is 15.7 kN/m3, and the saturated unit weight of soil below the water table is 18.8 kN/m3. Assume that the depth of the foundation will be 1.5 m and the tolerable settlement is 25 mm. Determine the size of the foundation.
A 3 m 4 m footing, founded at 2 m depth in a clay, applies a net pressure of 200 kN/m2. The bed rock lies 10 m below the footing. The modulus of elasticity of the clay is 30 MN/m2. Using Janbus generalized relationship [Eq. (17.1)], assuming undrained conditions and flexible footing carrying uniform pressure, estimate the expected settlement.
The table gives the standard penetration numbers determined from a sandy soil deposit in the field: Using Eq. (12.19), determine the variation of the peak soil friction angle, . Estimate an average value of for the design of a shallow foundation. Note: For depth greater than 6 m, the unit weight of soil is 18.55 kN/m3.
In Problem 16.3, if there was a surcharge of 20 kN/m2 at the ground level, what would be the total horizontal normal stresses at A and B? Use the results from Problem 16.3. 16.3 The soil profile at a site is shown Figure P16.3. Find the total horizontal normal stresses at A and B, assuming at-rest conditions.