For the network shown, obtain the complex bus-bar voltage at bus 2 at the end of the fourth iteration using Gauss-Siedel method. Line impedances shown in the figure are in per unit. Given: Bus 1 is slack bus with V, - 1.0/_0", P, + jQ--5.96+jl.46, V2 - 1.0/ 0° and V,-1.02

For the network shown, obtain the complex bus-bar voltage at bus 2 at the end of the fourth iteration using Gauss-Siedel method. Line impedances shown in the figure are in per unit. Given: Bus 1 is slack bus with V, - 1.0/_0", P, + jQ--5.96+jl.46, V2 - 1.0/ 0° and V,-1.02

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: Describe the principles and benefits of High Voltage Direct Current (HVDC) transmission systems, and…

A: HVDC transmission is based on the principles of converting alternating current (AC) to direct…

Q: b) Figure 4 shows a transmission line circuit using a 100 m long, low-loss 50 line of phase velocity…

Q: The sample power system subjected to three phase fault at bus 4. The system values are given below…

A: Find explanation below

Q: 4. The fuel-cost functions in $/h for three thermal plants are given by F = 500 + 5.3P, + 0.004P? F2…

Q: The five-bus system shown in Figure bellow has p. u. impedance as marked. The symmetrical bus…

A: Given figure is,Admittance matrix is,Asked to find the impedance matrix (or) Z matrix.

Q: 6.11. In the two-bus system shown in Figure 6.24, bus 1 is a slack bus with V₁ = 1.020° pu. A load…

A: Solution- Bus 1 => slack busBus 2 => PQ buswe have 2 unknown V and phase angle at Bus 2,∂P2∂δ2…

Q: Load flow analysis is used to calculate ________________ a. Transmission losses b. voltage…

A: Load flow analysis is a mathematical analysis which use various computational method to analyze the…

Q: Draw convergent and divergent positive characteristic lines on an x-t plane. Indicating the time and…

A: The objective is to draw the convergent and divergent positive characteristic lines on an x-t plane…

Q: What is the need to conduct power flow analysis? Discuss about data needed and bus types too.

Q: Q1: For a medium line model, draw the circle diagram only and put the value of OR, OS and 0t If you…

A: Three-Phase Line: Three-phase alternating current is a popular form of alternating current used in…

Q: B) Develop an expression, in terms of the generated e.m.f. and the sequence impedances (ZI, Z2 and…

A: Solution (B) - For phase A, the line to earth fault is shown below,

Q: (c) Why are resistors and inductors considered to be series impedance and capacitors considered as…

A: The performance of transmission line depends on the parameters of the line. The transmission line…

Q: V₁ = 120° P.U Slack bus (1) jo.05 P.U j0.2 P.U 0.4+j0.3 P.U (3) jo.025 P.U -(2) 0.8+ j0.6 P.U

Q: : The per-unit ractances for a given system are shown in figure below. (1 MVA) is being delivered to…

A: Step-1->

Q: By using Gauss-Siedal method, the voltage of the bus 2 after two iteration is Your answer By using…

A: Given,The data of a system are,Ybus=j0.25-0.2-0.05-0.20.225-0.025-0.05-0.0250.075…

Q: b. Formulate the admittance matrix for this system. yı2= -j5 Pp.Qr y12b= -j5 Pai.Qai yı= -j1 y2= jl'

A: According to question: b)…

Q: If the power system has 'n' number of generators, then the size of the B- coefficient matrix is…

A: As per the guidelines of Bartleby we supposed to answer first question only for remaining questions…

Q: Discuss the role of HVDC (high-voltage direct current) transmission systems in long-distance power…

A: High-Voltage Direct Current (HVDC) transmission systems operate by converting alternating current…

Q: A DC Optimal Power Flow problem is to be solved for a 3-bus network. The per-unit reactances of the…

A: The per-unit reactances of the lines A 3-BUS network interconnecting the buses are…

Q: E = 1.35460 0}} jol X'=j0.15 jous 0 + 11 jous V = 120⁰:1.0 V=ILO

A: In this question we need to check the system remains stable after one circuit of the lines is switch…

Q: In a Gauss-Seidal method of power flow studies,the network of 4 bus system consists of 6 equations…

A: We need to tell about G S method

Q: the amount of real and reactive power that flow between any two buses is determine by the relative…

Q: The Gauss-Seidel is an iterative method used to solve a set of nonlinear equations in the power…

A: Gauss-Seidel method is used to solve the power flow analysis question in the power system. In two…

Q: In power flow studies,if a network consists of a generator bus which elements of Jacobian Matrix…

A: Explanation: In power flow studies a generator bus which factors of a jacobian matrix is dealt with…

Q: Impedance matching is provided at D = 0.074? and L = 0.094? values for an unknown load using the end…

Q: ork why we need to consider the neutral impedance 3 times

A: The zero sequence components are in having the same phase in all the three phases. When there is a…

Q: Consider the same 4-bus system shown. Use the tie set method to determine the reliability,…

Q: In zero sequence impedance net work why we need

A: Zero sequence network models on a three phase basis shown in the below figure. The current flowing…

Q: Establish Zbus matrix for the system shown in figure below using Direct Method and add the lines…

A: According to the data given in the question. Z1=j0.1Z2=j0.1Z3=j0.4Z4=j0.6Z5=j0.4 It is given that…

Q: The load flow data for a three-bus system is given below. Taking bus 1 as the slack bus, determine…

A: P2 = 9, Q2 = 0.5, P3 = -2,Q3=-0.6

Q: In N-R method of Power flow solutions, in case of generator bus, the terms of derivatives with…

A: In the question, Choose the correct option The given Statment is true or false. This question is…

Q: By using Gauss-Siedal method, the voltage of the bus 2 after two iteration is By using Gauss-Siedal…

A: Initial guess values are:V1=1+j0V2(0)=1+j0V3(0)=1+j0Injected power into the system is:P2=-0.6 ,…

Q: In a Gauss-Seidal method of power flow studies,the network of 4 bus system consists of 6 equations…

A: From the load flows in power system

Q: For different types of buses/nodes in load flow analysis, explain their definitions and possible…

A: In power system analysis, buses/nodes are used to represent different components of the power…

Q: QI The fuel-cost functions in Sh for three thermal plants are given by 5 = 350 + 7.20P, + 0.0040P F-…

Q: How will you ensure minimum cost for the generation of required power for a given load? You may…

A: The science of calculating the cost of producing one kWh of electrical energy is known as power…

Q: What is the relationship between phase and line quantities in unbalanced star and delta connections?…

A: A star connection is one where every winding contains a single end linked to the same junction and…

Q: advantages and limitations of Gauss-Seidal and Newton Raphson methods . Of this two, which method is…

A: 1st we discusse the comparison Between G.S and N.R method. Then we study about the advantages and…

Q: Figure below shows the single-line diagram of three-bus power system with generation at bus 1 and…

A: For the given three-bus power system with generation at buses 1 and 3, we need to determine the…

Concept explainers

Compensation Techniques

The compensation techniques are the methods that are employed in the electrical control systems to enhance the performance of the system. The performance are generally affected by the factors like lag in the compensating devices, slow response of the system of the components like sensors used in the control system. The basic compensation technique involves lag compensation, lead compensation or the combination of the both.

Question

For the network shown, obtain the complex bus-bar voltage at bus 2 at the end of the fourth
iteration using Gauss-Siedel method. Line impedances shown in the figure are in per unit.
Given: Bus 1 is slack bus with V = 1.0/ 0", P, +jQ: =-5.96 + jl.46, V; = 1.0/_0° and V3 = 1.02
0.04 + J0.06
0.02 + j0.03

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6 Answer:

Step by step

Solved in 6 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Compensation Techniques in Transmission Line

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A DC Optimal Power Flow problem is to be solved for a 3-bus network. The per-unit reactances of the lines interconnecting the buses are as follows: X12 = 0.1pu, X13 = 0.12 pu and X23 = 0.2 pu. There is a generator at each bus. The loads at buses 1, 2 and 3 are 150MW, 200mw, and 100MWrespectively. Bus 1 is taken as the reference bus, and SBase = 100 MVA. Which one of the below is a constraint of the DCOPF problem? Select one: O a. None of these O b. -500 0₂-1000 03 = P3 - 110 O c. 1500 0₂-500 03 = P₂ - 220 O d. 1500 0₂-500 03 = P₂ - 200 O e. -500 0₂-1000 03 = P3 - 150 O f. -1500 8₁-1000 03 = P₁ - 150
Q2\ The one-line diagram of a simple power system is shown in figure below. All impedances are expressed in per unit (pu) on a common MVA base. All resistances and shunt capacitances are neglected. The generators are operating on no load at their rated voltage. A three-phase fault occurs at bus 1 through a fault impedance of Zf = j0.08 per unit. Using Thevenin's theorem obtain the impedance to the point of fault and the fault current in per unit. Determine the bus voltages and line currents of generators during fault. X₁ = = 0.1 XT-0.1 3 1 to ojo XL=0.2 2 040 X₁ = 0.1
The bus impedance matrix for a three-bus power system has per-unit elements as: Z11 = 0.5 Z12 = 0.4 Z13 = 0.8 Z21 = 1 Z22 = 0.5 Z23 = 0.6 Z31 = 0.5 Z32 = 1.2 Z33 = 1 Prefault voltage is 1 per unit and prefault current is neglected. A three-phase short circuit occurs at bus 3. Determine the subtransient fault current. Round your answer to 2 decimal places.
Following figure shows the one-line diagram of a two bus system. Take bus 1 as slack bus, bus 2 as load (PQ) bus. Neglect the shunt charging admittance. Obtain the bus admittance matrixYBUs and find V₂ and 62, power flows and line losses using FDLF method. All the values are given in per unit on 100MVA base. Use a tolerance of 0.001 for power mismatch. 1 Z12= 0.12+10.16 Slack bus V₁ 1.0/0⁰ pu 2 PL2=1.0pu Q12=0.5pu
Discuss the reasons that make the load flow problem non-linear.
One of the following load flow analysis method is found to be more efficient for large power systems. Gauss- Jordan Method Gauss- Seidal Method Newton- Raphson Method Gauss Method
bus. The voltage magnitude and phase angle are the quantities to be determined after load fiow analysis for
How do we handle a PV bus in the Gauss Seidel Method? What will happen to the bus voltage if the reactive power at a PV bus exceeds the upper bound? And why?
One of the following load flow analysis method is not more efficient for large power systems. Gauss- Jordan Method Gauss Method Gauss- Seidal Method Newton- Raphson Method
Power system
bus. The reactive power and voltage angle are determined at the end of load flow analysis for
4