6.11. In the two-bus system shown in Figure 6.24, bus 1 is a slack bus with V₁ = 1.020° pu. A load of 100 MW and 50 Mvar is taken from bus 2. The line impedance is z12 = 0.12 + j0.16 pu on a base of 100 MVA. Using Newton- Raphson method, obtain the voltage magnitude and phase angle of bus 2. Start with an initial estimate of |V₂|(0) = 1.0 pu and 5₂ (0) = 0°. Perform two iterations. 2 Note Onter 100 MW z12 = 0.12 + j0.16 V₁ = 1.040° -+, 50 Myar "Perform

6.11. In the two-bus system shown in Figure 6.24, bus 1 is a slack bus with V₁ = 1.020° pu. A load of 100 MW and 50 Mvar is taken from bus 2. The line impedance is z12 = 0.12 + j0.16 pu on a base of 100 MVA. Using Newton- Raphson method, obtain the voltage magnitude and phase angle of bus 2. Start with an initial estimate of |V₂|(0) = 1.0 pu and 5₂ (0) = 0°. Perform two iterations. 2 Note Onter 100 MW z12 = 0.12 + j0.16 V₁ = 1.040° -+, 50 Myar "Perform

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

I need the answer as soon as possible
How will you ensure minimum cost for the generation of required power for a given load? You may neglect transmission line losses. Support with mathematical formulations
Discuss the advantages and limitations of Gauss-Seidal and Newton Raphson methods . Of this two, which method is generally preferred for solving the load flow problems?
The one-line diagram of a 6-bus power system is shown below with per unit impedances on common base. Determine the YBus.
Figure below shows the single-line diagram of three-bus power system with generation at bus 1 and bus 3. The voltage at bus 1 is V₁ = 1.025/0° per unit. The voltage magnitude at bus 3 is fixed at 1.05 per unit with a real power generation of 250 MW. The scheduled load on bus 2 is marked on the diagram. Line impedances are marked in per unit on a 100 MVA base. Line resistances and line charging susceptances are neglected. By using Gauss-Seidel method and initial estimates of V₂(0) = 1.020° and V3(0) = 1.0520°, determine V₂ and V3. Perform calculation for one iteration. V₁ = 1.025/0° j0.1 Slack Bus j0.2 j0.4 j0.2 3 j0.1 250 MW 150 Mvar |V3|=1.05 P3 = 250 MW
In the Gauss-Seidel iterative method of power flow, describe the differences of the computational procedures used for a PV bus and a PQ bus.
one circuit of a sinlge phase transmission line is composed of three solid 0.5 cm radius wires. the return circuit is the composed of two solid 2.5 cm radius wire . the arrangement of conductors is as shwon in figure below. applying the concept of GMD and GMR , find the inductance of the complete line in millihenry per kilometer
bus. The voltage magnitude and phase angle are the quantities to be determined after load fiow analysis for
How do we handle a PV bus in the Gauss Seidel Method? What will happen to the bus voltage if the reactive power at a PV bus exceeds the upper bound? And why?
pls explain by computer line . in less than 30 min.
Power system
bus. The reactive power and voltage angle are determined at the end of load flow analysis for