For the frame shown below, assume El is constant for all members. Analyze the end-moments and end-shears for each member of the frame shown by the Slope-Deflection Method. Joints B and C are fixed, while joints A and D are pinned. a.) Draw the shear and moment diagram for the entire frame. b.) Make a rough sketch of the elastic curve for the entire frame. 10 KN A 5m 3 m

For the frame shown below, assume El is constant for all members. Analyze the end-moments and end-shears for each member of the frame shown by the Slope-Deflection Method. Joints B and C are fixed, while joints A and D are pinned. a.) Draw the shear and moment diagram for the entire frame. b.) Make a rough sketch of the elastic curve for the entire frame. 10 KN A 5m 3 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Solve using slope defelction method
Use CONJUGATE BEAM METHOD ONLY! E = 80 GPa & I = 1200x106 mm4 A. Find the Vertical Reaction at D in kN B. Find the Deflection at C in mm. C. Find the Slope of the elastic curve at D in Degrees Three Decimal places
Consider the frame shown. Suppose that w = 16 kN/m. a) Determine (approximately) the moment the ground exerts on the frame at joint A. Hint 1 for Part A. How to approach the problem Analyze the frame using approximate methods for statically indeterminate structures with vertical loads. Apply the required assumptions regarding zero moment points in order to reduce the frame to the one that is statically determinate. Then, use the equations of equilibrium to determine the moment exerted on the frame at joint A. Hint 2 for Part A. What assumptions should be made to solve the problem Since the girder located within a building bent and subjected to a uniform vertical load is statically indeterminate to the third degree, an approximate analysis will therefore require three assumptions to make the girder statically determinate. Each girder having the length L may be modeled by a simply supported span of length 0.8L resting on two cantilevered ends, each having a length of 0.1L.…
A simply supported beam carries a moment applied to one end as shown. El is constant. a) Calculate the support reaction forces for the beam b) Write out the M(x) equation using discontinuity functions. c) Determine the slope and deflection equations by integrating the M(x) equation as needed and using two B.C. to solve for the integration constants, C1 and C2. d) Calculate the deflection at the mid-span of the beam. e) Check: Calculate the deflection at point B (right support). A 12A
Please solve the problem in the picture, find all of the reactions and please show the shear, moment and Moment/EI diagrams. Thank you for your help!
Determine the slope and displacement at point B. Assume the support at A is a pin and C is a roller. Account for the additional strain energy due to shear. Take E = 29(103) ksi, I = 300 in4, G = 12(103) ksi, and assume AB has a cross-sectional area of A = 7.50 in2. Use the method of virtual work.
Fill in the blanks only.
USE CASTIGLIANO’S THEOREM For the beam shown, determine the displacement at D and the slope at D using the indicated method. Assume A is a fixed support, B is a pin, and C is a roller. Draw the SHEAR and MOMENT diagram. E = 200 GPa.
For the beam structure shown below, both C and E are rollers, support A is pinned. El is constant within the structure. (1) Determine the degree of indeterminacy of the structure. (2) Choose appropriate redundant(s), then apply the Force Method to calculate reaction forces at all supports. (3) Draw shear and moment diagrams of the beam (4) Apply the Conjugate Beam Method to calculate the vertical deflection at point B. -12 ft- 30 k ↓ B H -12 ft- -12 ft- E = 29,000 ksi I = 1,500 in.4 30 k ↓ D -12 ft-
Use moment area method.
solve fast