Please solve the problem in the picture, find all of the reactions and please show the shear, moment and Moment/EI diagrams. Thank you for your help! Problem 3: Using the moment area method, compute the slope and deflection at pointC. The flexural rigidity between A and B' is 2EI. The flexural rigidity is El from B' to C.4 m120 kN.m2A2EIB' EI BΕΙ8 m4 m

Answered: Image /qna-images/answer/dab95a67-17b3-434f-854e-50eabf02a26a.jpg

Answered: Problem 3: Using the moment area…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Solve this question asap with proper figures
1. For the frame shown below, the force P = 100 lb. a) Use the figures on the next page of this handout (or draw your own figures) to draw the free body diagram of the entire frame and of each member; show all forces, including directions, if known. b) Determine the components of all the forces acting on member CDEF. Specify the direction (→, e,1, J) for each. c) Redrawn member CDEF and shown all forces including the proper direction and proper magnitude. Ans: C = 80 lb. →, Cy = 60 lb. , Ex = 80 lb. →, E, = 60 lb. T, D, = 160 lb.<, D, = 100 lb. T %3D %3D |3| %3D 6 in. 4 in. 2 in. E F 3 3 in. 2 in. A 4.
Explain in detail, the effect of the direction of current and alternative load application point of the structure members (include the names and formulas) in the figure below
Civil Engineering: METHOD OF JOINTS Use the given information to answer. Thank you!
FORMAT: QUESTION FIGURE FBD REQUIRED COMPLETE SOLUTION ANSWER I WILL UPVOTE IF YOU FOLLOW ALL OF THESE. THANK YOU
Two wires support a weight W. The stresses in the wires AB and AC are not to exceed 81 MPa and 161 MPa, respectively. The cross- sectional area of the two wires are 353 mm? for AB and 139 mm2 for AC. Wire AB is inclined 23-degrees with the horizontal and wire AC is inclined 46-degrees with the horizontal. Give the largest weight W (kN) that can be supported by the wires? Answer in two decimal places. Numerical values only. Don't indicate units here, just on the submitted solution. B A W
Consider Problem 5.50.Solve the same problem again, but this timeyou are asked to place a support somewhereunder the span of the bean in order to minimize the maximum normal stress of in the beam?Explain your work,your results, and your assumptions.Where did you place thesupport? Use no more than 50 words. Provide cleardrawings that areclearly annotated
Please answer this one. show complete solution including necessary figures. Please write neatly
Please help me answer the problem with a solution and box the final answer. Thank you for helping me DONT FORGET TO WRITE IT ON CLEAN PAPER.
O (6) Facebook e.com/courses/7419/assignments/132721 Maps 国Reading WRITE YOUR NAME AND YOUR ID NUMBER. PLACE YOUR SIGNATURE AT THE LOWER RIGHT CORNER OF YOUR ANSWER SHEET DRAW THE FIGURE. PROVIDE COMPLETE SOLUTION. NOT FOLLOWING INSTRUCTION WILL GET ZERO. Determine the reaction at supports and compute the force in members: df, ca, cd, and cf (You may use any method.) Tabulate your final answers: MEMBER// FORCE, KN// COMPRESSION OR TESNSION 5m 130° 40KN 5m 5m 6m Show all 99+
Pratt Truss Calculate the internal resultant forces in each member of the Pratt truss by hand for a given load of F = 1000 lbs. Since the problem is linear, doubling the load will double all the internal resultant forces, halving the load will halve the internal resultant forces and so on. Figure out what is the load, F, and the internal resultant forces in each of the members when one of the members is at 500,000 lbs.
2 ● Find all reactions (Moment & forces) at A and B through method of consistent deformations Note: you must replace fixed support with MUST pin connection a Draw moment diagram

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

Problem 3: Using the moment area method, compute the slope and deflection at point C. The flexural rigidity between A and B' is 2EI. The flexural rigidity is El from B' to C. 4 m 120 kN.m 2 A 2EI B' EI B ΕΙ 8 m 4 m