* For the cross section shown in the figure. :Find the value of Y 40 mm A1 250 mm

Q: The solid axle has a diameter of 40 mm. It is subjected to a shear force of 1 1. kN along Z-axis and…

A:

Q: The cross-sectional area of a wide-flange I-beam has the dimensions shown. Obtain a close…

A: Let us divide the given shape into three rectangles with the dimensions highlighted in below figure:

Q: The cantilever beam is supported by a fixed support at A, and subjected to the force F = 600 lb and…

A:

Q: A steel beam, of lengths a=5 m and b= 2 m and a hollow box cross section, is supported by a hinge…

A: Here reaction force along x-direction at pin support A is neglected as there are no applied force…

Q: The principal stresses at a point in an elastic component are 61 62 63. For given values of 02 and…

A:

Q: 1. A circular shaft with a keyway can be approximated by the section shown in Fig. r=b r 0 r =…

A: To Find : The value of constant K. Given : The prandtl stress function form is ψ=Kb2-r21-2acosθr The…

Q: Determine the torsional stress of the cantilever shafts show in the figure below: C 200 5 KN.m T 15…

A:

Q: Mohr's circle for an element is shown, each grid is 5 MPa square. A rotated plane through the…

A:

Q: The square deforms into the position shown by the dashed lines in (Figure 1). The dimensions are…

A: Given- S=49 mm, S′=54 mm, Δx1=5 mm, and Δx2=9 mm.Determine the shear strain at D relative to the x,…

Q: Determine the torsional stress of the cantilever shafts show in the figure below:

A: Outer diameter, d1=20 mm=0.02 mInner diameter, d2=15 mm =0.015 mTorque, T=5 kN.mLength, L=200 mm=0.2…

Q: 25 kips 20 in.- Figure 1 10 in. 25 kips 20 in. B 7.25 in. Sin.- b 1.5 in. 1.5 in.

A:

Q: For the beam shown, find the reactions at the supports and plot the shear-force and bending-moment…

A:

Q: The solid shaft is loaded (two point loads) and supported (fixed at left end) as shown. For the xyz…

A: AS this Question as multiparts solving first part or you can mention the part  Given data -: 1. dia…

Q: 6. A shaft of different diameters is planted to the wall at A and is subjected to torque loadings,…

A: For the solution refer below images.

Q: Determine the maximum value of Qof the Transverse Shear Stress formula [T = (VQ)/(It)] at point p in…

A:

Q: Determining the resultant of the internal loads acting on the cross section at C of th

A:

Q: se Mohr's circle to find the stress on the slope indicated by the dotted line when the stress state…

A:

Q: Find the resultant shear stress at point A & C for the weldment shown in the figure. Leg size of the…

A:

Q: 0.75 m 0.5 m D B P 1.25 m A

A:

Q: The material used for section CB of the shaft shown has an allowable shear stress of Tallow= 75 MPa.…

A: Data given -

Q: For the following Mohr's circle: can we find the normal stress in X, the normal stress in Y and the…

A:

Q: A) Determine the shear strain γxy at corner C. B) Determine the shear strain γxy at corner D.

A:

Q: 65mm 375mm M 115mm 115mm 65mm 57mm

A:

Q: A steel beam, of lengths a=5 m and b=5 m and a hollow box cross section, is supported by a hinge…

A: To find:The maximum normal stress in the cross-section of the beam (in MPa).Given data:A steel beam…

Q: Given the section is subjected to a moment of 500 N-m, calculate the normal stress in MPa at the…

A:

Q: 2. If the bending stress at section 2 =20 MPa. What are the bending stresses at sections 1, 3, and…

A: Given data:        From equation of pure bending                                MI=σby=ER…

Q: The wood beam has an allowable shear stress of Tallow MPa. d3 t d1 d2 V d1 P d5 d4 = = 9.6

A: To findDetermine the Q at point P.Determine the moment of inertia, I.Determine the magnitude of the…

Q: A force of F = 13 kips is applied as shown in the figure below. If the diameter of the bolt is d =…

A: Given data:- force (F) = 13 kips  the diameter of the bolt (d)= 1.4 inches, To find:-the maximum…

Q: The cross-sectional area shown is subjected to V = 600 kN and M =1000 kN-m. What is the flexural…

A:

Q: section shown in figure Question 2, determine the shear stress a. In the Web at point A b. and in…

A:

Q: Determine the resultant internal loadings acting at the circular cross- section passing by points A…

A:

Q: (YC)zy = Submit Part B Value (YD)zy = Request Answer Determine the shear strain Yzy at corner D.…

A:

Q: A bolt passing through a piece of wood is shown below. Determine the average shear stress in the…

A:

Q: Given the stress element shown, determine the maximum in-plane shear stress. 0x = 54 MPa Oy = 30 MPa…

A: Given:σx=54 MPaσy=30 MPaτxy=40 MPaFind:The maximum in-plane shear stress.

Q: A bar of a uniform cross-section is rigidly fixed at one end and loaded by an off-centre tensile…

A:

Q: M E. х Solution: The moment of inertia of the cross-section about z and y axes are 1 Iz AB³ |(10-)…

A:

Q: Determine the total stress at point A on the cross section a-a in the figure below. 400 kN la -0.5…

A: Draw a diagram showing the neutral axis for the above-cross section.

Q: 2. The figure below shows a shaft with pulley and gear. Find the location along the x axis where the…

A:

Q: 3444 stress at the POI. Make sure that you label the shear and bending moment diagrams with all…

A: Given data  Ay = 12.67 k By = 29.33 k  y = 0.1026 ft I = 0.00526 ft4 and cross-section of beam…

Q: The cross-sectional area of a wide-flange I-beam has the dimensions shown. Obtain a close…

A:

Q: g) the value of the deflection at point C. Enter your answer in mm to three decimal places. Assume…

A:

Q: A wide flange beam as shown below is subjected to a shear force V. Using the dimensions of the cross…

A:

Q: Given P = 1.5 kN, M = 1.4 kN.m (clockwise), 0 = 55°, and a = 2 m, what is the resultant internal…

A: Given data: P = 1.5 kN M = 1.4 kN.m θ=55°a=2m Need to determine the normal force on the…