The rigid beam shown in is held by two vertical rods at A and C. If a 60 KN load is applied at B what is the displacement of this point (B) Steel L 4m Aluminum L-3 m A 500 mm E- 70 GPa A= 300 mm E- 200 GPa 3.5 m 2.5 m

The rigid beam shown in is held by two vertical rods at A and C. If a 60 KN load is applied at B what is the displacement of this point (B) Steel L 4m Aluminum L-3 m A 500 mm E- 70 GPa A= 300 mm E- 200 GPa 3.5 m 2.5 m

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.3.7P: -7 Repeat Problem 2.3-5, but n include the weight of the bar. See Table I-I in Appendix I for the...

See similar textbooks

Related questions

Q: Question 4: Two wrenches are used to tighten the pipe. If the pipe is made from a material having an…

Q: Don't Use Chat GPT Will Upvote

Q: The uniform steel (E =200 GPa) bar in Fig. has a diameter of 40 mm and is subjected to the loading…

A: According to the given data E=200GPa d=40mm L=AB=BC=CD=200mm We need to find Displacement of…

Q: Rigid bars AB and BCD are supported by pins A and D and by a steel rod at C. There is a roller E =…

Q: Answer: Wmax = kN/m B

A: According to the given dataL=1.7md=18mmWe need to find the uniform distributed load w

Q: Q1/A/ Two steel bars AB and BC support a load P=30 kN as shown in figure 1. Area of AB is 300 mm²,…

Q: 800 N 120 N.m d = 8 cm 600 N Q /If the cross section of the femur can be approximated as a circular…

A: Stress due to eccentric axial load of 800N P1=P2=800N P2 and 800N will create a moment M=800(0.8)=64…

Q: Figure 2: Given the below determine the bar force at AB. (Answer in whole number, indicate the…

A: Answer: The force in the bar AB: FAB = -28.3 kN (Compression).

Q: What are the magnitude (F) and the location measured from end A (d) of the equivalent resultant…

A: Ans-a(F=10.5KN, d=6m)

Q: and (D). Calculate the stress he loads are applied, and ement of point (B). Use E =

A: given:

Q: The figure shows the cross section of a circular steel tube that is filled with concrete with a…

A: Find the stress in concrete.

Q: A rigid strut ABCD supports two concentrated loads P at points B and D. It is being supported by a…

A: Given: The area of cable, A = 120 mm^2 = 120 x 10-6 m2 The elastic modulus of the cable, E = 50 GPa…

Q: A force of F = 13 kips is applied as shown in the figure below. If the diameter of the bolt is d =…

A: Given data:- force (F) = 13 kips the diameter of the bolt (d)= 1.4 inches, To find:-the maximum…

Q: The cross-sectional area shown is subjected to V = 600 kN and M =1000 kN-m. What is the flexural…

Q: As shown in the figure below, determine the internal loadings at points A,B and. Consider the…

Q: M E. х Solution: The moment of inertia of the cross-section about z and y axes are 1 Iz AB³ |(10-)…

Q: 8000 lb 3000 lb 7000 lb 2000 lb 4' 5' 3' Fig. P-208 and P-209. up (73 208. An aluminum bar having a…

A: To find: The total deformation. Give: The Young's modulus is E=10×106 psi. The cross sectional area…

Q: A standard truck moves across a 25- meter span. The wheel loads are P1=36 kN and P2=142 kN separated…

A: Given: The distance between wheel, x = 4.3 m The distance between load 2 and 3, y = 7.6 m The…

Q: Problem: The steel pipe has an inner diameter of 2.75 in and an outer diameter of 3 in. The pipe is…

A: To find: (a) The normal and shear stress at point A and B. (b) The principle stress at point A and…

Q: and P₂ (KN) as shown. Analyze the system of axial bars if the allowable stress requirement and axial…

Q: 5-4 Composite A-36 steel bar shown made from two segments AB and BD. Area AAB = 600 mm2 and ABD =…

Q: The rigid bar AB of negligible weight is supported by a pin at O. When the two steel rods are…

Q: The ratio J2/J1

A: Given: ⇒ r3>r1 and r4>r2

Q: A solid aluminum shaft of 100 mm diameter fits concentrically in a hollow steel tube. Determine the…

Q: Question 1: Given that Tattow = 50 MPa for the rod AB and tattow = 25

A: given:shear stress for AB =50Mpashear stress for BC=25MpaT=1250N-m

Q: What are the magnitude (F) and the location measured from end A (d) of the equivalent resultant…

Q: When a force P of 750 N is applied to the pedal shown in the figure, find the diameter (mm) of this…

Q: 5. If the elongation of wire BC is 0.2 mm after the force P is applied, determine the magnitude of…

A: Given Data: Diameter of wire, d=3 mm Modulus of elasticity of wire, E=200 GPa

Concept explainers

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.

Question

The rigid beam shown in
is held by two vertical rods at A and C.If a 60 KN load is
applied at B what is the displacement of this point (B) .
Aluminum
L- 3m
A- 500 mm
E- 70 GPa
Steel
L- 4 m
A= 300 mm
E- 200 GPa
3.5 m
2.5 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Design of Power Transmission Elements and Power Transmission Systems

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Repeat Problem 11.3-9. Use two C 150 × 12.2 steel shapes and assume that E = 205 GPa and L = 6 m.
1. Rod ABCD is made from two materials with two cross sectional areas. The rod is subjected to axial loads as shown. Neglect the weight of the rod and determine the displacement of point A. EBE Ep =210 Gla 125 kN EAg = 70 GR ABE Aco=900 u AAB = 450 mm 37stEN/ %3D 2m 2.5m
Q4
The uniform 44 kN bar BC is supported by a pin at C and the aluminum wire AB. The cross-sectional area of the wire is 178.5 mm2. Assuming bar BC to be rigid, find the vertical displacement of B due to the weight of the bar. Use E = 71 GPa for aluminum. Anwer must be in mm.
แสดงวิธีทำให้ดูหน่อย
แสดงวิธีทำให้หน่อยครับ
plz help before -ront The shaft is supported at its ends by two bearings A and B and is subjected to the forces applied to the pulleys fixed to the shaft. (Figure 1) The T₁ 410-N forces act in the - direction and the 200-N and 80-N forces act in the +y direction. The journal bearings at A and B exert only y and components of force on the shaft. Figure lashel but sol is 300 mm A 200 mm 2 150 mm 150 mm ✓ 200 mm 400 mm B. 200 N 200 N 80 N 80 N 1 of 1 ▾ Part B Determine the resultant shear force in the y direction on the cross section at C Express your answer to three significant figures and include appropriate units. (Vc)y=245.714 Submit Part C Submit * Incorrect; Try Again; 3 attempts remaining Check your signs. (Vc),= 175 ▾ Part D Determine the resultant shear force in the direction on the cross section at C. Express your answer to three significant figures and include appropriate unite. T= 10 ▾ Part E Previous Answere (Mc) Submit M ^ Part Fi * Incorrect; Try Again; 5 attempts remaining…
مقاومة المواد
The assembly consists of three titanium (Ti-6A1- 4V) rods and a rigid bar AC. The cross-section area of each rod is given in the figure. If a force of 60 kip is applied o the ring F, determine the horizontal displacement of point F. Hint: Refer to the textbook appendix for material properties. AEF 2 in² 1 ft = 60 kip F-2 ft- 2 ft A C 6 ft B AAB = 1 in² E ACD = 1.5 in² 6 ft D
For the assembly shown, determine the displacement of point B and D as the load of 50KN is applied at D. Rod BC is steel with length = 2m, A = 600mm2 E=200GPa. Bar ABD is rigid. What is the stress in the rod CB? What is the shear stress of the bolt of the pin at A if it's diameter is 20mm? B im Detail of the pin at A
Question 1: Given that Tuitow = 50 MPa for the rod AB and tattow = 25 MPa for the rod BC. If T=1250 N.m, find the required radius for both rods. Ahmtmum AB = BC =
F2 Q1) Axial displacement of point C in the system shown on the left is 0.01 cm. Find the maximum elongation of the bar and the maximum normal stress. A F1 A. GIVEN: F2 = 100 kN, (1 = 240 cm, €2= 160 cm, bi = 5 cm, bz=10 cm, h=5 cm, E=2.107 N/em², a=20 cm Note: neglect stress concentration. h bị b2 A-A section