I need a clear answer by hand, notby keyboard and fast answer within20 minutes. Thank you | dybala. For the composite structureshown in Figure, draw the shearforce and bending momentdiagrams of part (ABC).A4m10 kN/mBAAA4mCLink 2mD

To draw the shear and moment diagram for the span ABC.

Answered: For the composite structure shown in…

For the composite structure shown in Figure, draw the shear force and bending moment diagrams of part (ABC). A 10 kN/m A 4m B 4m C Link 2m M D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Calculate the bar forces GI,GE and GD of the truss system for the loading situation given in Figure…

A: Trusses are structural members which are composed of a minimum of 3 members and act as a unit body…

Q: Determine the maximum tensile and compressive bending stresses in the beam shown. 4 kN/m 10 kN 6 m B…

Q: 150 mm 150 mm 150 mm 150 mm 650 mm As = 4 - 32 mm 75 mm

Q: For the cantilever beam with uniformly distributed load shown in Figure 2. Use (bf hf.bw, hw) for…

Q: Determine the maximum load based on shear design at critical section and at 1.5m from the support of…

A: the critical section for shear stress is if the support reaction introduced compression in end…

Q: The W12×40 section in Fig. below is used as a simply supported beam. Two point loads applied at the…

Q: Normal force, moment and shear diagrams and cross section given below according to their…

A: non circular soil section are torsionally week because shear stress distribution is non…

Q: depth of the neutral axis.

A: Given: Width of the beam, b = 200 mm Depth of the beam, D = 400 mm Clear cover, cc = 40 mm Diameter…

Q: Determine the concentrated load at midspan that can be added if the uniformly distributed load o is…

A: We have to determine the value of concentrated load at midspan that can be added if uniformly…

Q: For the truss shown in Figure 2.3b, determine the force in member AM if x = 7 m, y = 3 m, and P = 13…

Q: Determine the maximum compressive bending stresses (MPa) in the beam shown

A: Moment in portion AB:

Q: For the pin-jointed frame shown below: 100 kN C 4 m B 3 m 90 kN- D. 4 m 6 m- Find forces in member…

A: Given arrangement, To find force in members AE,AB,BD

Q: 20 k- 20 ft 40 k- E F | 20 ft 60 k B C 30 k 60 k - 3 at 30 ft = 90 ft

A: To find force in member HI and EI

Q: alculate the required amount of tensile reinforcement so that a tensile strain of 0.005 is attained…

A: given-a rectangular beam are limited to b = 300 mm and effective depth, d = 700 mm. Using f’c = 28…

Q: MPa, Clear cover= 40 1.What is the flexural capacity of the beam at face of the support KNm? 2. What…

Q: A beam has a cross section show below. If the stress at point P is 30Kpa , calculate the value for…

A: Given values Shear stress = 30kpa Shear force, V= ? Formula used -> shear stress = V*Yc*A/INA*t…

Q: From the truss frame loaded as shown in figure. Determine the bar forces in each member and indicate…

A: To find force in all members Here we will use both method of section as well as method of joint to…

Q: calculate the support reactions b. using the method of sections draw the shear force diagram AND…

Q: Analyze the Truss by stiffness method as shown in figure below. Take point p load equal 36 Note:…

A: given data,P=36KNtaking moment at 5 point ∈M5=0R1×2=36×4R1=72KN∈H=0R1+R5=0R5=-72KNat joint…

Q: For the truss shown in the figure, calculate the stresses in members DE and BD. The cross-sectional…

Q: For the structure shown in Figure P-916 is hinged to fixed supports at A and E. Compute the maximum…

Q: For the truss shown in Figure 2.3b, determine the force in member DG if x = 5 m, y = 3 m and P = 6…

Q: A simply supported beam is subjected to two point loads, each P = 340 lb, as shown in the figure..…

Q: For the frame shown above is constructed out of circular tubes for both the beam and column. It has…

A: Value of P can be calculated using the bending equation

Q: The dimensions of a rectangular beam = 770 mm. SIT D. are limited to b = 300 mm and h %3! Assume…

A: Note - answer for tension reinforcement area should be 3839mm2.

Q: n, solve the absolute maximum shear stress.

A: CALCULATIONS OF ABSOLUTE MAXIMUM SHEAR STRESS###

Q: Q4 - For the given beam and cross section, at point B on section A-A (mid-span), determine the…

Q: A 7.3 m B C 2 6.4 kN 8.0 kN D 1.9 m - 4.0 m

A: The truss is analyzed with the help of equilibrium equations The sum of vertical forces is equal to…

Q: Question 8 Consider the below truss. Given: Applied load P = 33 kN, vertical reaction at H Hy = 33…

A: Using joint method

Q: The W12×40 section in Fig. below is used as a simply supported beam. Two point loads applied at the…

Q: A truss is detailed in figure below. For the given loading, determine the magnitude and nature of…

Q: 300N/m 450N-m 100N-m 2m 5m 2m 100 200 Figure 2 All dimension are in mm

A: Consider the beam as shown below.

Q: The truss structure in the figure is supported by a roller at Land hinge at M. When Fo=65 kN. (a)…

A: The following members of the truss structure in the image are zero-force members:BE, EC, FG, GQ, HP,…

Q: Exercise No. 1: Draw the shear and bending moment diagrams for girder AB. Also determine the maximum…

A: The algebraic total of all the forces operating on either side of the section is known as the shear…

Q: Questions a/b c₁₂=c 200 10 E 5 0.291 m 20 40 289 10 0.312 200 0.323 0.328 10 1. 6.3 kNm torque is…

A: For given data:Torque = 6.3 kN-mLength of the shaft = 3mCross-sectional area, a= 5090 mm2Modulus of…

Q: 1.5 kN 3 kN B C 3 m 3 kN D E 3 m F G 3 m 3 kN 3m H I 3 kN 3 m K 1.5 kN 3 m 16.75 m L

Q: For the following problems use an allowable stress equal to 25 ksi for both tension and compression.…

A: A truss is a construction made up of parts arranged in linked triangles such that the entire…

Q: Based on your b and considering a positive bending moment of 58kNm, determine the tensile and…

A: Given section is:

Q: Pratt roof truss is loaded as shown in the figure. Using the method of joints, determine the force…

Q: The beam shown has a rectangular cross section 4 in. wide and 8 in. deep. Determine the maximum…

A: Given data : Depth (D)=8 inWidth (B)=4 in

Q: (1)Calculate the maximum bending stress. (2)Compute the maximum web shear stress in MPa. (3)Compute…

Q: The rigid beam shown is supported by a pin at A and two steel rods each of diameter 16 mm. I P = 30…

Concept explainers

Loads and Reactive Forces

Loads are the external influences that a beam experiences under its working conditions. For instance, a beam may be subjected to shear loads, twisting loads, bending moment, and axial loads during its working conditions. Engineers primarily deal with beams and trusses in the civil engineering domain. Due to the influence of loads, it is very crucial to determine the induced stresses and deformation values. These values give an insight into the critical area of the beam that needs to be worked upon to make it fail-safe.

Question

I need a clear answer by hand, not
by keyboard and fast answer within
20 minutes. Thank you | dybala
. For the composite structure
shown in Figure, draw the shear
force and bending moment
diagrams of part (ABC).
A
4m
10 kN/m
B
AAA
4m
C
Link 2m
D

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Introduce the problem

VIEW

Step 2: Solve the problem

VIEW

Step 3: Calculate the Shear and Bending moment Values

VIEW

Solution

VIEW

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

is strengthened by bolting two cover The wide-flange beam shown in Fig. plates 160 mm by 20 mm to the top and bottom flanges. If the maximum flexure stress is 140 MPa, compute the total force (a) in each cover plate and (b) in each flange. Neglect the weakening effect of the bolt holes. 160 mm 20 mm 20 mm 320 mm 20 mm €20 mm
Determine the maximum tensile and compressive bending stresses in the beam show.
Please show all steps
The steel truss (E =200 GPa) shown in figure below has a cross-sectional area of 1920 mm². Determine: a. The largest allowable load F if the change in length of member BD is not to exceed 1.6 mm and a factor of safety of 2.5. b. The displacement of support D due to the load calculated in part a. 5m 6m A C F
An over hanging beam ABC of length 10 m (including over hang portion) is shown in the figure below. The ratio of ILD ordinates at C to ILD ordinates at B for the shear force at B is A B 7 m 3 m-
Need all accurate solution
For the given girders of the frame shown which carries a uniform load of 12 kN/m along span GH and HI and a uniform load of 36.2 kN/m along span DE and EF. Dimensions are given as follows: A = 3.7 meters B = 5.1 meters C = 7.4 meters Using the approximation for building frames under vertical loads. G [A] [A] [B] [C] Compute the value of the absolute moment at reaction B. (kN-m) « Previous Quiz save
anwser 2nd part
The beam shown here is made of wood with an allowable shear stress of τall = 1100 psi. If PB = 5 kips, determine the maximum allowable force PC that can be applied on the structure before the beam fails in shear.[LAB= 2 ft, LBC= 2 ft, LCD= 1.5 ft, b = 1.25 in., h = 7 in.] Determine the maximum value of the first moment of area (Q) for the beam. (in^3) Determine the maximum allowable force at C (PC) that can be applied on the structure before it fails in shear. (kips)
stresses in beams 3.
For the truss shown in Figure 2.3b, determine the force in member KP if x = 5 m, y = 7 m and P = 7.94 kN. Indicate whether the member is in tension or compression. (Note: Use negative sign (-) if the member is in compression.) 7 panels at x m = 7x m В J D K L y F A х М N H G P P kN P kN