i need the answer quickly For the circuit shown below if Vi is reduced to 100 mV, the voltage VL=................+V₁-200 mVR₂2012pnpR.100 kSKO VL85V O15V50V25V45VIf you have a diode of power rating 10 W. The voltage across it is IV and the current passingthrough it is 2 A What is the power dissipation ?*<10 W OO4 W20 WO6 W O

Note : As per our guidelines we are supposed to answer one question only. So please post remaining…

Answered: For the circuit shown below if Vi is…

For the circuit shown below if Vi is reduced to 100 mV, the voltage VL = V₁-300 V 2092 100 k SKO VL 85V O 15V O 5ον Ο 25V O 45V O

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Help please
Complete solution otherwise skip. Plxxx.
What is the total number of systems?
Ture or false
What is ampere circuital law?
b) Remove the following complements using DeMorgan's theorems. ______________________ ___________________ _____________ P+ Q + (C+D.E'). (F+G) Please write the solution handwriting.
Please provide Handwritten answer. Electrical Engineering A 15 KHz tone is recorded at 8000 Hz. The frequency of the tone when played back at 8000 Hz is ____ KHz
i need the answer quickly
Refer to the National Electrical Code® or the working drawings when necessary. Where applicable, responses should be written in complete sentences. For problems 1 and 2, six luminaires, similar to Style E used in the Commercial Building, are to be installed in a room that is 12 ft x 18 ft (~3.7 m x ~5.5 m) with a 9 ft (2.8 m) floor-to-ceiling height. The spacing ratio for the luminaire is 1:0. 1. The maximum distance that the luminaires can be separated and achieve uniform illuminance is ft ( m). For problems 2-5, two luminaires, 8 ft (2.5 m) and 4 ft (1.2 m) in length with dimensions as shown in Figure 15-7, are to be installed in tandem (end to end). The end of the long luminaire is to be 2 ft (600 mm) from the wall. 2. The center of the outlet box should be roughed in at ft ( m) from the wall. 3. The first support should be installed at the wall. ft ( m) from 4. The second support should be installed at from the wall. ft ( m) 5. The final support should be installed at the wall. ft…
22surse_assessment_id=_18982_1&course_id=_22058_1&content_id= _262244_1&ques * Question Completion Status > A Moving to another question will save this response. uestion 2 If the switch is closed for a long time and then opened at t-0. What is the initial value of the capacitor's voltage? ww None of the answers o 12 O Take Test: Quiz 2-. FUJITSU F10 F11 F12 Prt Scr E7 F8 F9 F6 Sys Rq ECO 7 V 8 A 9. 5 Y ! U P
Please, I need the final solution as soon as possible, I do not need any explanation or explanation
Complete the following text with words Pt100 sensors are a specific type of _____(1) detector. The most important characteristic of Pt100 elements is that they are made of _____(2) with an electrical resistance of _____(3) ohms at a temperature of ______(4) °C and temperature coefficient ____(5). It is by far the most common type of RTD sensor. The other materials with which RTDs are built are: ___(6), _____(7), ______(8). The most recommended conditioning method is reading at _____(9). Typically, a _____(10) behavior of the Resistance-Temperature relationship can be assumed.