For the calibration data given, plot the calibration curve using suitable axes. Estimate the static sensitivity of the system at each X. Then plot K against X. Comment on the behavior of the static sensitivity with static input magnitude for this system. Y [cm] 4.76 4.52 3.03 1.84 X [kPa] 0.05 0.1 0.5 1.0 321 D

For the calibration data given, plot the calibration curve using suitable axes. Estimate the static sensitivity of the system at each X. Then plot K against X. Comment on the behavior of the static sensitivity with static input magnitude for this system. Y [cm] 4.76 4.52 3.03 1.84 X [kPa] 0.05 0.1 0.5 1.0 321 D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Given the following discrete time system where y[n] is the system output and x[n] is the input, indicate which of the provided options are the discrete poles of the system. yln] = 0.7y[n – 1] – 0.4y[n – 2] + 2x[n – 1] + 4x[n – 3] Select one: O a. 0.5 + j0.9634 O b. 0.35 + j0.52 O c. -0.25 + j0.45 O d. 0.35 + j0.152
4:07 3G l. Moodle A bbb2.du.edu.om EE ...Session (15-3- Said Grami O College of Engineering Vision for the Future Question 3 During a step function calibration, a first-order instrument is exposed to a step change of 200 units. 1- If after 1.5 s the instrument indicates 140 units, find the instrument time constant. 2- find the error in the indicated value after 2 s S. 3- Find the raise time at 90 % of the system. y(0)=0 units; K=1 unit/unit. Question 4 A first order instrument with a time constant of 2 seconds is to be used to measure a periodic input. If a dynamic error of ±2% can be tolerated, 1- determine the maximum frequency of periodic input that can be measured. 2- What is the associated time lag (in seconds) at that frequency? MECH374: Instrumentation and Measurement Said Grami Practice
For the calibration data given in Table Q2(c), plot the calibration curve using suitable axes. Estimate the static sensitivity of the system at the midrange.
Answer the following questions, to test your understanding of sampling frequency and bit depth. 1. You are part of new automobile design team, and are responsible for designing the sensor data collection system. The specification of the data collection system is that is must be capable of receiving data with a resolution down to 0.1% of full scale (1 part in 1000) for any given sensor. For example, suppose the driver pushes the gas pedal, the motion of which is read by an electronic sensor such that the range of motion is defined from 0 (not pressed) to 1 (fully pressed). If you want 0.1 % accuracy, you need 1000 possible data values between 0 and 1. How many bits do you need to represent data to 0.1% accuracy? Insert a picture of your work.
The orthographic views of an object are shown below. a) Draw its isometric drawing using a pencil. Provide all important dimensions on your isometric drawing. b) You need to take pictures of all main steps and need to provide a step-by-step method to draw isometric drawing accompanied by pictures. 307303030 | 20 60 15 15 55 30 20 60 + 27.5 4 25 47.5 25 R20 20 T 15 60 016 120 R30 120 120 30
Lab 2-Measurement Asynch - Tagged.pdf Page 4 of 7 ? Part I: Taking Measurements & Estimating Uncertainties for a single measurement www.stefanelli.eng.br The mass of the object is_ 0 i Parts on a tripie peam palance 0 0 10 20 30 1 100 2 3 40 200 4 +/- 50 60 70 5 300 7 400 80 Qv Search 8 90 9 500 100 9 10 g www.stefanelli.eng.br
r:09 moodle1.du.edu.om An application demands that sinusoidal pressure variation of 250 Hz be measured with no more than 2% dynamic error. In selecting a suitable pressure transducer from vendor catalog, you note that a desirable line of transducer has a fixed natural frequency of 500 Hz but that you have a choice of transducer damping ratio of between 0.5 and 1.5 in increments of 0.05. select a suitable transducer. The value of damping ratio is between the following values Select one: O a. 0.707 and 0.807 O b. 0.631 and 0.692 c. 0.2356 and 0.5625 d. 0.5215 and 0.5625 Previous page Next page 1 Assignmen II
Please help me to Draw an isometric sketch of the component
Mechanic
In your biomechanical testing lab, you perform a series of compression tests to determine the relationship between apparent bone density (p, units of g/cm³) and ultimate stress (ơult, units of MPa). Using the set of experimental measurements below, write an m-file to fit a power relationship of the form O uli = Ap to the data. Use the log transform method to linearize the system and data, followed by linear regression. Plot the data points and the power relationship on a single plot. Be sure to label your axes and provide a legend. Provide a printout of your m-file and a printout of the command window showing your results. Write down the best fit equation and box it. 8.76 5.25 4.26 5.51 3.88 18.45 2.09 13.72 5.42 2.17 Oult (MPa) p (g/cm³) 0.598 | 0.459 0.319 | 0.235 0.141 0.754 0.177 0.553 0.394 0.246
Subject: Mechanical Measurements Do not copy online solutions. It's different value
In matlab code