For the beam shown, do the following: 1. Determine the values of shear at every change of load points by the Area Method and mark the maximum value. 2. Determine the values of moment at every change of load points by the Area Method and mark the maximum value. 3. What is the moment at a point 3m from the left end? 4. What is the slope of the shear diagram at the exact point C? 5. Draw the elastic diagram. All lengths are in meters. There is a pin at Point B and fixed support at A... 1okulm 2m

For the beam shown, do the following: 1. Determine the values of shear at every change of load points by the Area Method and mark the maximum value. 2. Determine the values of moment at every change of load points by the Area Method and mark the maximum value. 3. What is the moment at a point 3m from the left end? 4. What is the slope of the shear diagram at the exact point C? 5. Draw the elastic diagram. All lengths are in meters. There is a pin at Point B and fixed support at A... 1okulm 2m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A P = 10 kip 1.5 ft B C 2 ft The bars in the structure to the left are pinned and have circular cross-sections. The diameter of the cross- section is 1.5 inches. The bars are made of steel, which has an elastic modulus of 29,000 ksi. A point force of 10 kips is applied at point C, as shown. What is the change in length of member BC? Is the bar getting longer or shorter?
1.1 Show your complete solution.
The frame shown in the figure is supported by a hinge at E and roller at D. Compute the horizontal and vertical component of the hinge force at C. as it acts upon BD *use 3 decimal place in rounding off all throughout the solution.
From the given simply supported beam below, determine the following: a, The shear and moment equation of each segment of the beami Use point A as reference of b. The Shear and Mament Diagram of the beam e The maximum shearand moment of the beam. d. The moment of Ihertia with respect to the neutral axls. e. The maximum flexurál stress and shear stress of the beam. I. The bending stress at point B andC * The shear stressät the mid-point of the beam. 20 kN 14 kN / m 10 KN / m A B [D] E 4 m 25 m 25 m 3 m 360 mm 80 mm 130 mm 130 mm 300 mm 90 mm 280 mm
UPVOTE will be given! Please write the solutions completely and legiby. Box the final answer. Strength of Materials
The right angle bar is supported by a pin at B and a roller at C as shown in figure. The 30 mm diameter pin is in double shear. The shear stress in the pin is limited to 120 MPa. Neglect torsional effect. 400 mm BC The maximum safe value of Pis 30° P 480 mm kN. (Round off to one decimal place)
A. Calculate the shear force in the pin at B in pounds. B. Calculate the shear stress in the pin at B in psi.
.
A hollow steel crank has an outside diameter of 57 mm and an inside diameter of 52 mm. The load magnitudes are Py= 400 N and P, = 210 N, and the length dimensions are a = 125 mm, b = 344 mm, and c = 225 mm. y Py K Pz b Determine the magnitudes of the equivalent forces and the equivalent moments that act at the section that contains point K. (a) Axial force in x direction Px (N) (b) Shear force in y direction V, (N) (c) Shear force in z direction V, (N) (d) Torque around x axis Tx (N-m) (e) Bending moment around y axis M, (N-m) (f) Bending moment around z axis M, (N-m)
the bell crank as shown in the figure is in equilibrium determine the shearing force in the pin D. Please include Free body diagram and show complete solution
4 pls have fbd