3. The beam BE is used for hoisting machinery. It is anchored by two bolts at B, and at C it rest on a parapet wall. The essential details are given in the figure. Note that the bolts are threaded as shown in Detail 1 with d=0.620 in. at root of the threads. If this arrangement is used to lift equipment of 10 kN, determine the stress in the bolts BD and the bearing stress at C. Assume that the weight of the beam in negligible in comparison with the loads handled. B Timber nominal Section 20cm x 30cm Bolts diam.%" 28 cm D 1m View A-A C₁ 18 cm 20cm 2.5 m Building 111 P=10 kN Detail 1 D d F E 111 Distributed Force equivalent to F Threaded bolt

3. The beam BE is used for hoisting machinery. It is anchored by two bolts at B, and at C it rest on a parapet wall. The essential details are given in the figure. Note that the bolts are threaded as shown in Detail 1 with d=0.620 in. at root of the threads. If this arrangement is used to lift equipment of 10 kN, determine the stress in the bolts BD and the bearing stress at C. Assume that the weight of the beam in negligible in comparison with the loads handled. B Timber nominal Section 20cm x 30cm Bolts diam.%" 28 cm D 1m View A-A C₁ 18 cm 20cm 2.5 m Building 111 P=10 kN Detail 1 D d F E 111 Distributed Force equivalent to F Threaded bolt

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Note: Read the question thrice then after solve it. I have other websites answers please don't copy that solutios. Thank you
The triangular plate shown with uniform thickness has a mass M = 129 kg. Use x = 1 m and y = 1.5 m. A load P = 529 N is also applied at position indicated. Determine the tension (in Newtons) developed in cables A, B, and C.
Need asap pls. Thanks.
1. Answer Set A only
The change in diameter of the large steel bolt is carefully measured as the nut is tightened. Knowing that the initial diameter d = 50 mm, E = 190 GPa, and ? = 0.27, determine the internal force in the bolt if the diameter is observed to decrease by 0.009 mm after the nut has been tightened. Assume that the supports shown are fixed and rigid. d
Kindly answer d, e, f, and g only.
The five 20mm-diameter rivets fasten the plate as shown in the figure to the fixed member. a). Determine the value of the load P so that the average stress of any rivet does not exceed 80MPa.b). What additional clockwise torque can be applied before the shearing stress exceeds 90MPa
At the beginning of your solution, write down the values of P1, P2, P3 and L and solve the followings using the section method: 4- The internal member force FBC; 5- The internal member force FBE.
The assembly shown below is pinned at A & C and A & C are subjected to a double shear. Let each pin diameter be 18 mm, and P = 20 kN. Find the:a) Force at the rod BC (kN) and force acting on pin A (kN)b) Average shear stress at A (MPa), and average shear stress at C (MPa)
Please provide a detailed solution especiallyl for the moment of inertia and how you got the values etc. The book of Beer's manual solution does not provide a detailed solutino and it is hard to understand.
The bell-crank mechanism is in equilibrium for an applied load of F1 = 19 kN applied at A. Assume a = 280mm, b = 170mm, c = 80mm, and θ = 45°. Pin B is in a double-shear connection and has a diameter of 30 mm. The bell crank has a thickness of 29 mm. Determine the bearing stress in the bell crank at B. Express your answer in MPa rounded to the nearest tenths.
Two forces, each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is 15.3 mm. Determine the largest allowable value of P (in N) if the shear stress in the shaft is not to exceed 87.95 MPa and its angle of twist is limited to 5.41°. Use G = 80.32 GPa for steel and L= 433 mm. Round off the final answer to two decimal places. ... P -300 mm P- B L A