For question 103A and 103B, the thin-walled cylindrical container shown below. Say p is the internal pressure of 15MPA, d is the inside diameter of the container of 20mm, and t is wall thickness of 10mm. See figure 103. Question 103A, the longitudinal stress is nearest to * Girth joint d Longitudinal joint Figure 103

For question 103A and 103B, the thin-walled cylindrical container shown below. Say p is the internal pressure of 15MPA, d is the inside diameter of the container of 20mm, and t is wall thickness of 10mm. See figure 103. Question 103A, the longitudinal stress is nearest to * Girth joint d Longitudinal joint Figure 103

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please read the instructions carefully and do what are asks. Illustrate and show the COMPLETE SOLUTIONS.
An aluminum [E-9600 ksi] control rod with a circular cross section must not stretch more than 0.34 in. when the tension in the rod is 2070 lb. If the maximum allowable normal stress in the rod is 12.9 ksi, determine: (a) the smallest diameter d that can be used for the rod. (b) the corresponding maximum length L of the rod. Answers: (a) d- i in. (b) L- in.
Question.
How would maximum load change if temperature was increased? Maximum change in depth is 0.4mm.
In the Figure 5, the normal stress on the cross- sectional area is (in Mpa): Figure 5: y P = 400 KN X 30 mm 1000 mm 30° Area 20 mm الاختيارات 577 597 587 567 O O O
Question 1 Two circular rods of 50 mm diameter are connected by a knuckle joint, as shown in Figure 1, by a pin of 40 mm in diameter. If a pull of 120 kN acts at each end, find the tensile stress in the rod and shear stress in the pin. 50 x 11.00 in Rod (1) Pin Rod (2)
Q1: The beam shown in Figure 1 is subjected to a vertical force Pv and a horizontal force Ph The data for Pr, Pñ, atand eare-shown in Table 1. Determine the maximum compressive and tensile stresses under the vertical force (at a distance a from the left support.) Pv = 5. KN 30omm a Gomm Ph 14mm 120 mm L = 2400mm Figure 1 250 mm
As shown in the figure, three wires with different areas and modulus of elasticity are used to lift a load W. Their unstressed lengths are L1, L2, and L3. (a) What stress exists in the longest wire, and (b) shortest wire? (c) Determine the stress in the shortest wire if W = 500 Ib. (d) What should be the load so that the two wires will stretch to the length of the longest wire?
Note that : σ2= 14 σ1=30
The tensile stress in the AB bar is in the BC bar in order for it to be the same as the pressure stress, the Force P in the figure must be how many. F=170 N , LAB=85 mm , LBC=85 mm , DAB=51 mm , DBC=102 mm
A planar stress element has the stress state: 0₂ = 16 MPa, 0 = 44 MPa and ty = 39 MPa. Through what angle would you rotate the element to find the orientation that has zero shear stress? Units for your solution will be degrees. Ţ: Txy Tor 6 + 8
A state of plane stress is illustrated in the stress element in Figure 3. (a) (b) 30 MPa Figure 3. 40 MPa 60 MPa y X Find the center, X and Y of the Mohr circle. Plot the Mohr circle using these points. From the Mohr circle, find the principal stress and the maximum shear stress. Indicate on the Mohr circle where these values are found.