A state of plane stress is illustrated in the stress element in Figure 3. (a) (b) 30 MPa Figure 3. 40 MPa 60 MPa y X Find the center, X and Y of the Mohr circle. Plot the Mohr circle using these points. From the Mohr circle, find the principal stress and the maximum shear stress. Indicate on the Mohr circle where these values are found.

A state of plane stress is illustrated in the stress element in Figure 3. (a) (b) 30 MPa Figure 3. 40 MPa 60 MPa y X Find the center, X and Y of the Mohr circle. Plot the Mohr circle using these points. From the Mohr circle, find the principal stress and the maximum shear stress. Indicate on the Mohr circle where these values are found.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.19P: At a point on the surface of an elliptical exercise machine, the material is in biaxial stress with...

See similar textbooks

Similar questions

An element in plane stress on the fuselage of an airplane (figure part a) is subjected to compressive stresses with a magnitude of 42 MPa in the horizontal direction and tensile stresses with a magnitude of 9.5 MPa in the vertical direction (sec figure part b). Also, shear stresses with a magnitude of 15.5 MPa act in the directions shown. Determine the stresses acting on an element oriented at a clockwise angle of 40g from the horizontal. Show these stresses on a sketch of an element oriented at this angle.
An clement m plane stress from the frame of a racing car is oriented at a known angle 8 (sec figure). On this inclined clement, the normal and shear stresses have the magnitudes and directions shown in the figure. Determine the normal and shear stresses acting on an clement whose sides are parallel to the \y axes, that is, determine crv, tr(_, and t, Show the results on a sketch of an clement oriented at B .
At a point on the surface of an elliptical exercise machine, the material is in biaxial stress with t = 1400 psi and trv = —900 psi, as shown in the figure part a. The figure part b shows an inclined plane aa cut through the same point in the material but oriented at an angle ft Determine the value of the angle 6 between zero and 90° such that no normal stress acts on plane aa. Sketch a stress clement having plane aa as one of its sides and show all stresses acting on the clement
-27 A square plate with side dimension of 2 in. is subjected to compressive stress a and tensile stress The stresses on element A oriented at angle ?? x1=45° aresy1= 75 psi. tx1y1= 275 psi. . Find the state of stress on the element lilt is rotated clockwise to align the x3 axis with the horizontal x axis.
Do not answer in image format. Answer completely.
Consider the general case of plane stress as shown. Write a computer program that will show a plot of the three Mohr’s circles for the element, and will also determine the maximum in-plane shear stress and the absolute maximumshear stress.
To determine the normal and shear stresses on the indicated plane, we must first determine the orientation of the inclined plane relative to the x face of the stress element. Determine the magnitude of the counterclockwise angle between the x face and the inclined plane. Assume Sx = 170 MPa, Sy = 105 MPa, Sxy = 85 MPa, and ß = 65°. Sx Sxy В Sy Answer: 0 = 25 X O'
At a point of a material, the stresses forming a two-dimensional system are shown inFigure Q1. By using Mohr's circle of stress method: -(i) determine the magnitudes of the principal stresses.(ii) determine the directions of the principal stresses.(iii) Examine the value of the maximum shearing stress.
The state of plane stress at a point is represented on the element shown in the figure below. (a) Determine the principal stresses acting on this point, and the corresponding orientation (angle). (b) Determine the maximum in-plane shear stress, and the corresponding orientation (angle). Also determine the associated average normal stress. Draw Mohr's circle and show the stresses on the circle. 15 ksi 23 ksi 14 ksi
The state of plane stress at a point is represented by the element shown in the figure. Oy o, = 200 Mpa oy = 450 Mpa Txy Try 3D200 Мра Click here to see all formulas Ox Part A - Determine the maximum principal stress in Mpa. O 253 О 355 O 507 O 760 O 608 Submit Request Answer O O O O O
The stresses acting on element A in the web of a train rail are found to be 'X (MPa)' tension in the horizontal x-direction and 'Y (MPa)' compression in the vertical y-direction. Also, shear stresses of magnitude 'S (MPa)' act in the directions shown in the figure. Draw Mohr's circle for the state of stress. Determine the stresses (Ox', Oy' and Txy') acting on an element oriented at an angle 'D' from the horizontal Show these stresses on a sketch of an element oriented at this angle X=45MPA,Y=150MPA,S=52MPA,D=-40 Degree
EMFT