For Problems 5.50 to 5.52, compute the design moment strengths of the beams shown if fv = 420 MPa and fc (prime) = 21 MPa. Check the maximum permissible A, in each case to ensure ductile failure. E, =200,000 MPa Problem 5.51 2022 4 #36 375 mm 70 mm 680 mm 750 mm

Q: From the following table, develop network diagram, determine the critical path, and Calculate the…

A: Given:- The activity and duration of the activity is given  To determine:- The critical path  The…

Q: Activity IPA Activity IPA D B D, E C, F, G C, G C A, B H, I FGHH

A:

Q: What kind of documentation should be done by the field personnel?

A: Few accurate notes were maintained, and all of the contractor 's correspondence was informal in…

Q: A constraint is a limitation to the amount of resources needed to perform an activity. physical…

A:

Q: 6- --It is the smallest time taken to complete the activity if everything goes on well A- Most…

A:

Q: Why is the Resident Project Representative responsible for the record-keeping system?

A: Resident Project Representative is a person working on a project, typically on a full-time basis, to…

Q: Q: Figure I shows the activities of a small project with their details. 1. Draw the Gantt chart of…

A: Introduction- A project organization diagram depicts the logical and sequential link between…

Q: (a) What is the irmportance of a job lay-out ? Sketch a typicai job layout for R.C.C. framed 9.…

A:

Q: What situation does Industrial Surveys is applicable?

A: Industrial surveys are field surveys, which is one of the functional classification of surveying.…

Q: EC, LS, LC, TF, and FF. Preceding Activity Time A,F

A: Given:- Network diagram To find:- total project duration ES,EC,LS,LC,TS,FF

Q: What are the factors of change order preparation?

A: Change orders are among the most common forms of construction delays, budget overruns, driving scope…

Q: Q2) Find the total duratlon and date of completion (assume the project start date is 10/6/2019) by…

A: Gantt chart : A Gantt chart is a form of bar chart that depicts a project timetable. It is named…

Q: Draw the original network and calculate the CPM values, then check the effect of these updates and…

A:

Q: A constraint is a limitation to the space needed to perform an activity. O physical technical…

A: Activity is characterized as the measure of work played out that converts contribution to proper…

Q: Question 24 Resource is a situation in which more resources than available are assigned to an…

A: Answer Resource Allocation Resource allocation is the way or process used to assigning and…

Q: construction site A that was recently issued a stop-work order from the artment of Safety & Health…

A: The condition when there is injury, illness, health damage, or death i.e. Fatality of the person on…

Q: Frontier of Flight Museum with a one-paragraph SUMMARY in which I make it clear how this reportis…

A: The objective of this question is to provide a detailed report on a visit to the Frontier of Flight…

Q: Q- ... was a work progress schedule that required in engineering design steps. O Network analysis…

A: Critical Path method is a widely-used project management technique for scheduling projects. This…

Q: Homework I: Draw the network diagram by using AOA lechnique for the following activities, define the…

A: Solution Given Data Draw the network diagram AOA Technique

Q: Show in calculation the project status if it is behind, ahead, or on schedule: 10K A AA 11K 12K 10K

A:

Q: Homework2: Draw the network diagram by using AON technique for the following activities, define the…

A: Given:- The time duration of the following activities are given:- Activity Preceding Activity…

Q: SITUATION 6 A project network is shown as below together with the breakdown of activities. START…

A: Critical path : Critical path is that type of path where sequence of activities determines the…

Q: Q1: Determine the duration of project for the activities shown below, and find the critical path by…

A:

Q: ratio

A: PERT uses three estimated times for activity duration optimistic time The estimate is determined…

Q: Activity durations for a 5km piping project are listed below. The minimum time buffer between…

A:

Q: The top-down approach is typically used on simple projects in which the tasks and schedule are…

A: the answer is false

Q: Who uses the PERT Management Control System?a

A: PERT stands for Program Evaluation and Review Technique, is basically a management technique or…

Q: How is the CPM scheduling program helpful to the Engineers?

A: The Critical Path Method (CPM) scheduling program is an activity-oriented network program used for…

Q: Describe the steps taken for the development of inspection plan?

A: Inspection of any sort of work is an important parameter for ensuring its safety, performance and…

Q: Activity A started as planned- took 2 more days. Activity B started on day 5, was completed in the…

A: The network diagram given in the question is as follows-

Q: cated activities on the critical pat fES, EC, LS, LC, TF, and FF.

A: Given:- activity,precedent activity,time To find:- total project duration ES EC LS LC TF FF

Q: How to answer this question in an interview as a recent grad, ability to communicate in writing…

A: There are different types of the communication. We can communicate with others by using the writing…

Q: What is non excuseable delay?

A: Non-excusable Delays are defined as the delays which are within the control of the contractor and…

Q: why do you think it is so expensive to develop a software patent?

A: Because patent is unique which not present in the world right now. It is the right of that object…

Q: Homework3: Draw the network diagram by using AON technique for the following activities, define the…

A:

Q: A Gantt Chart is used for planning, scheduling and monitoring projeets, and managing th dependencies…

A: 3) False Gantt chart is used for planning, scheduling but it can't show interdependency between the…

Q: Interviewers intentionally smile to applicants to keep them on their toes. * (1 Point) S-If the…

A: in this question one statement is given and we are asked to identify the given options

Q: What is S-curve scheduling?

A: To define the S-curve scheduling we need to understand the S-curve. An S-curve could be a…

Q: Why do the Field personnel use BIM?

A: A method of building elements describes the geometric features, spatial orientation, geographic…

Q: Q/Find the completion time and critical path for a project with following: 5 H 4 15 3 2 M 10 A 8 C.…

A: There are activities named from A to M and their durations , overlapping times between successor…

Q: What preparations can be made for close out project?

A: Project closure activities make sure the recording project documents, archiving in structure method…

Q: From the following table of information: a) Draw the precedence diagram; b) What is the probability…

A:

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.