For controlled half wave rectifier, R=80ohm, f=50Hz and Vm=280V and a=0,2 rad. Calculate the rms load current (A). In your calculations, take 3 digits after the comma and take pi = 3,14; Enter your answer into the system in terms of the desired unit only as a number.

Q: A de shunt moton Yuns at lo0o Y.P.m From q 5 00 V SUPPIY when taking an armature currant of 5 A.…

A: The given data's are, The speed N1=1000 rpm, The voltage V1=500 V, V2=250 V, The armature current…

Q: : Plot the relationship between the applied voltage and : :) No-load current. b) Power factor . c)…

A: Electrical machines can be either generator or motors. They can be either Ac machines or DC…

Q: In 4-point starters the resistance is added in series with NVC because __________________ a) To…

A: At the starting of the motor, Back emf (Eb) will be zero, hence a very high current flows through…

Q: Name 3 applications for closed-loop system

A:

Q: What are the poles according to their duties?

A: The function of poles is to support the conductors. poles should be capable to carry the load due to…

Q: explain Cell Relay with its application

A: Cell relay is a network technology used for transmission of data by using small data packets of a…

Q: The __________________ condition of the power system gives the  power flow solutions when the…

A: The explanation is as follows.

Q: With example and figure explain hysteresis, dead zone?

A: 1) Hysteresis 2) Dead zone

Q: Compare between armature resistance and synchronous resistance.

A:

Q: b) Draw a diagram of a Phase Locked Loop (PLL), describe the operation of the PLL.

A: Given: Diagram of Phase Locked Loop and its operation.

Q: With neat diagram explain the principle and working of motor used in lifts.

A:

Q: Give a real time example of an open loop system and explain with neat diagram the operation of it.…

A: an open-loop system is a type of control system in which the output of the system depends on the…

Q: Airframe Electrical System Question: In general, what factors areconsidered when selecting the…

A: While manufacturing, the sizes of the wire are selected according to a known standard called as…

Q: Explain the different type of routin test In CB ??

A: There are different kinds of routine tests done for the Circuit Breaker.   Power frequency…

Q: Discuss the importance of safety in an engineering maintenance from Kasapreku’s case scenario?

A: Answer:  The food and beverages industries has a moral and regulatory obligation to keep the work…

Q: Explain with a neat block diagram the measurement of displacement using RTD (measuring system).

A: Thermistor is a special type of Resistor whose resistance changes with the change in temperature.…

Q: what is nuisance tripping?

A: Nuisance tripping is the repetitive tripping of the RCD in absence of any serious hazard. The…

Q: What is the purpose of sequence control

A: Sequence control is generally used to start or stop motors in a specific order. It is used when one…

Q: A compound generator is to Supply aLoodof 250lamps; -each radedtoow, 250v.CTnear mature, series dind…

A:

Q: Draw the equivalent circuit of class E chopper for the Different quadrant operation and write its…

A:

Q: B. The series field of a short-shunt d.c. genera- tor is excited by ..............currents. (a)…

A:

Q: Why is proper grounding important?

A: Ground potential:  Ground potential has zero reference level used in a system to measure and apply…

Q: Explain the concept of motherboard power phases and their impact on system stability and…

A: We need to discuss motherboard power delivery systems, including voltage regulators and phases. We…

Q: Explain the concept of load shedding in power systems. How does it help in maintaining system…

A: Load shedding in power systems is a controlled and deliberate reduction of electricity supply to…

Q: 1. Give a real time example of an open loop system and explain with neat diagram the operation of…

A:

Q: In chopper control method, load current is discontinuous in most cases.

A:

Q: Give a real time example of an open loop system and explain with neat diagram the operation of it.

A: Open Loop system: An open-loop system is a type of continuous control system in which the output has…

Q: Does the guidelines provided by NEC is maximum

A: The solution is provided in the following section:

Q: Describe the ultimate cycle method, including the satisfactory perfor- mance. Also briefly discuss…

A: For system the maximum slope line starts at its origin , the delay is identified as the time at…

Q: QUESTION 13 The resistance of the Armature's conductor coil(s) in most motors is: quite high,…

A: The resistance of armature conductors are very low of range 2 to 4 ohm the reason behind the low…

Q: A typical home-type ceiling fan motor draws ____ watts. This is approximately 0.4 to slightly over…

A: GENERALLY, CEILING FANS ARE HAVING INDUCTION TYPE OF MOTORS WHICH ARE DRAWING  CURRENT FOR THE BUILD…

Q: What are the advantages of high voltage transmission?

A: Introduction The bulk transfer of electrical energy from generating power plants to electrical…

Q: Which stability is called as load stability? Why it is called like that?

A: Under the normal conditions, after the system is subjected to a disturbance the ability of a power…

Q: A motor has a full-load current rating of 74.8 amperes and the terminations are rated for 75°C. What…

A: Ans. 3 AWG 75°C CONDUCTOR,

Electrical Heating Unit

The conversion of electrical energy to heat energy is known as electric heating. The heating system that converts the electrical energy to heat energy for various application is called electrical heating unit. Electricity is employed as the firing mechanism in electric heating systems, which transforms electric current to heat. Electric heaters have heating elements in the form of electric resistors.