For an FM modulator with modulation index m (as in table modulating signal v„(t) = cos(2nf mt) Fm as in table Q1), and %3D an unmodulated carrier v.(t) = 10 cos (2nf t) (f.as in table Q1) Assume R,=502 i) Determine the number of sets of significant sidebands. ii) Determine their amplitudes. iii) Draw the frequency spectrum showing the relative the amplitudes of side frequencies.

For an FM modulator with modulation index m (as in table modulating signal v„(t) = cos(2nf mt) Fm as in table Q1), and %3D an unmodulated carrier v.(t) = 10 cos (2nf t) (f.as in table Q1) Assume R,=502 i) Determine the number of sets of significant sidebands. ii) Determine their amplitudes. iii) Draw the frequency spectrum showing the relative the amplitudes of side frequencies.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

a. Sketch the transfer curve for the device in the figure below. b. Determine IDg and VGSQ using the transfer curve c. Calculate Ipo and VGSQ for the circuit below 12 V 1.2 ka loss = 12 mA Vaso V =-4V 1 MA 1.5 V.
4. For a full-wave phase control circuit draw the output voltage and current waveforms when firing angle α = (45-X) °. (Here X= 1813)
Q2The modulating x(t)=2cos2000nt+cos4000nt is applied to AM modulator of carrier=2cos106 t. Write expression for modulation equation and Sketch the spectral of modulator output (Single Side Bandspectrum)
A modulating signal f(t) has a maximum frequency of 18 kHz and peak value of 3volt, this signal is encoded using PCM. 1- Calculate the number of bits per sample if the number of levels is 130 2- Calculate the SNRQ if the average power of f(t) is 45 watt. 3- Calculate the minimum system bandwidth. e 7:20
Consider a step down converter supplied by a DC power source of magnitude Vs = 220 V. The switching period is 0.1 ms and the duty cycle k is set to 0.5. The load is an inductive load with R=5 Ohms and L=10 mH. The switch is ideal. The RMS converter current IR is equal to 15.56A. The ripple factor of the input current RFs would be equal to: Select one: a. 0% Ob. 50% Oc. 100% d. None of these
For the circuit shown below: 1) Calculate the DC bias point for the transistor. 2) Estimate the midband gain with B= 100, Ic =ImA, R-SKS, RL = Rag=5KO, Rs- 100K2, VCC = VEE = 10V. 3) With Ca =C2-47µF and CE-47uF, what is the value of the approximate low frequency pole? Ve Ce
1. Suppose the MOSFET drawn has Vth = 1 V, and ID = 1 mA when Vov = 0.5 V. Vin Vin VDD = 5V I R₂ = 5 kn Vout Vs.VD. VDD t t (a) Calculate the Vin values that lead to off, linear, and saturation modes respectively. Indicate the boundaries of these regions on the Vin plot. (b) Draw a suitable 100 mV amplitude sinusoid for Vin that keeps the MOSFET working in saturation mode. (c) Draw three time-domain waveforms for VS, VD, VDD that correspond to Vin from part (b).
5-If the FM modulating signal is 300 kHz, and the carrier swing is 300 kHz. Therefore, the value and the type of the modulation index are, a) 0.5 NBFM b) 0.5 WBFM c) 1 NBFM d) 1 WBFM 6- IF the modulation index of FM signal is 2, the number of significant sidebands which greater than 1% of unmodulated carrier is? (Follow the table in the last page) a) 4 sidebands b) 6 sidebands c) 8 sidebands d) 10 sidebands 7- Let the carrier given 10cos(2nd) and the message signal be 5cos(10mt). Assume the message is used to frequency modulate the carrier with ky-10, the modulation index is, a) 1 b) 5 c) 10 d) 15
A balanced modulator with a carrier frequency input of 453kHz and an audio range of 300Hz -3.1kHz would have: a) a lower sideband extending from 449.9kHz to 452.7kHz. b) a bandwidth of 2.8kHz. c) an upper sideband extending from 453kHz to 456.1kHz. d) a 455kHz carrier. To enable a DSB receiver to receive SSB signals would require: a) a BFO. b) a higher IF. c) a redesigned RF amplifier. d) the LO to be replaced by a BFO.
.
Explain the high frequency response of CS MOSFET Amplifier with proper equation. Discuss the effect of parasitic capacitances.
(a) Explain on the AM Single Sideband Full Carrier (SSBFC) and compare to DoubleSide Band Full Carrier (DSBFC) on their:(i) Basic concept and operation.(ii) Peak change in envelope.(iii) Bandwidth.