Question 3: For single sideband (SSB) modulation a) Write the time domain equation XSSB(t). b) Explain the generation process of single sideband (SSB) signal using phase shift method. c) Sketch the block diagram of single sideband (SSB) signal generation using phase shift method and using bandpass filter and its main disadvantages. d) Explain with drawing the demodulation process of SSB signal. e) How many single sideband (SSB) stations can be accommodated in a 180 KHz bandwidth if the highest modulating signal frequency fmax is 9 KHz? f) What are the main advantages and disadvantages of single sideband (SSB) modulation compared with ordinary amplitude modulation (AM).

Question 3: For single sideband (SSB) modulation a) Write the time domain equation XSSB(t). b) Explain the generation process of single sideband (SSB) signal using phase shift method. c) Sketch the block diagram of single sideband (SSB) signal generation using phase shift method and using bandpass filter and its main disadvantages. d) Explain with drawing the demodulation process of SSB signal. e) How many single sideband (SSB) stations can be accommodated in a 180 KHz bandwidth if the highest modulating signal frequency fmax is 9 KHz? f) What are the main advantages and disadvantages of single sideband (SSB) modulation compared with ordinary amplitude modulation (AM).

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Derive a relationship between the time constant RC, and modulation index.
Choose the correct statement(s) that describe the diagram below. $(1) A.A.K Phase detector 0 (1) K, f'(-)dt Select one or more: a. Used to analyze the modulation trapezoid b. Used to demodulate angle modulated signals c. Linear PLL model Od. Narrowband to wideband conversion e. Non-linear PLL model Loop filter Loop amplifier Demodulated output
Q2: A modulating signal is used to modulate a carrier signal(AM modulation). Let Pr , Pc, PSB, PUSB, PLSB and u are the total power, carrier power, side band power, upper side band power, lower side band power and modulation index respectively. Prove the following: c. Puss = PLSB = Pr (2+m2
An audio signal given by 15 sin(4000ntt) + 20 sin(8000mt) amplitude modulated(DSB-FC) a sinusoidal carrier wave 60 sin(100,000nt) a. Derive an expression for the modulated signal. b. Find the modulation index. c. Find the spectrum of the modulated signal. d. Sketch the spectrum of the modulated signal e. Which type of demodulation method you propose to reconstruct the audio at receiver. Why?
Theoretical calculations: 3. How dose the bandwidth change in relation to increasing signal amplitude? FM
For single sideband (SSB) modulation a) Write the time domain equation XSSB(t).b) Explain the generation process of single sideband (SSB) signal using phase shift method.c) Sketch the block diagram of single sideband (SSB) signal generation using phase shift method and using bandpass filter and its main disadvantages.d) Explain with drawing the demodulation process of SSB signal.e) How many single sideband (SSB) stations can be accommodated in a 180 KHz bandwidth if the highest modulating signal frequency fmax is 9 KHz?f) What are the main advantages and disadvantages of single sideband (SSB) modulation compared with ordinary amplitude modulation (AM).
1. The CT signal x(1)-6cos (800zt) + 8cos² (mæt) is eritically sampled (Nyquist rate) by f-8000 Hz. Find: i. The value of m. ii. The frequency components of the signal. The frequency resolution (A) of the output spectrum if the sampled signal is processed by 32point-DFT. iii. iv. Define frequency resolution.
Explain how does LCR circuit work, impedance of LCR circuit in resonance, condition for resonance in LCR circuit and also discuss quality factor in LCR circuit?
Provide a simple sample problem with correct solution regarding practical bandwidth calculation for frequency modulation (FM).
Discus the Time Response Analysis and the Frequency Response Analysis. Discuss the Bode plot and Nyquist (Polar) plot to estimate the system stability and comment.
If the amplitude of the modulation signal voltage was given to be -4v and +4v and carrier amplitude also given to be -22v and +22v, by suitable waveform diagram determine the Am modulated output. Remember to provide all necessary wave forms in practical terms.
Discuss in detail about the narrowband noise and analyze the properties of in- phase and quadrature components of narrow band noise.