For a soil element the strength properties are given as c = 50kPa and > = 15 degrees. 3.1 Find σ1 at failure if σ3 = 100KPa. 3.2 For the failure condition given in (a) find shear and normal stresses. 3.3 Plot the Mohr- Circle at failure. [9 marks] [10 marks] [6 marks]

For a soil element the strength properties are given as c = 50kPa and > = 15 degrees. 3.1 Find σ1 at failure if σ3 = 100KPa. 3.2 For the failure condition given in (a) find shear and normal stresses. 3.3 Plot the Mohr- Circle at failure. [9 marks] [10 marks] [6 marks]

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

E.(upper) = Em Vm + EpVp Em Ep Vm Ep + VpEm The mechanical properties of aluminum may be improved by incorporating fine particles of aluminum oxide (Al,O,). Given that the moduli elasticity of these respectively, 69 GPa and 393 GPa, plot the modulus of elasticity versus the volume percent of Al,0, in Al from 0 to 100 vol.%, using both E (lower) = %3D of materials are, 55 350 50 300 45 40 250 Upper bound 35 upper- and lower-bound 200 30 Lower bound expressions. 150 25 20 15 100 20 40 60 80 Tungsten concentralion (vol%) Madulus of elaticty (GPa Modulus of elasticity (10 ps)
A strip of elastomer was stretched in tension and elongation was held constant. After 10min the tensile stress in the specimen dropped by 12%. Assuming that the elastomer behavesin accordance with the Maxwell model:• calculate the relaxation time (to the nearest whole number) (answer: τ = 78 min)• show that it takes 22 min for the stress to drop to 75% of its initial value.
Specification of Support Beam Dimensions You are asked to design a support beam used to suspend a heavy load under tension. The beam has a square cross section and is made of steel with a nominal yield strength of 325 MPa. What are the minimum dimensions of this beam if it must suspend a mass of 10,000 kg? Assume a factor of safety of 4.
Pls help ASAP
69 Gpa, = 0.35)is loaded by an axiel force of 3N, m24mm 12mm 15mm (al Delermine he avetuge ponnal stress ln sechon AB and BC of the chaft at locations away from thefillet Section AB, = Section BC, o rid (O)Determine the change of thee diameter in seien AD due to Polsson's effect. Section AB, Ad%= (c) Determine te hrbest nonnd stress al the filt consideing sTnss concentration. Athe fillet, o= (d) Determine the nommal and shear stresses on the oblique surface that has an inxline angle of Fwiththe nomal cross secbon of the shaft in section AB as shown. pwa the otlique
liquid hydrogen (LH2) tank is a double-hulled tank composed of cold drawn and annealed 316 stainless steel, with the cryogenic liquid on the inside and vacuum in the annular space (the outer tank). The Yield Stress of 316 stainless steel is 45 MPa, the Ultimate compressive strength is 90 MPa, the elongation % is 30, Poisson's ratio is .3 and the CTE is 15.9 *10-6 C-1. A. If there are no relief valves and the vessel is new, if the cross-sectional area of the inner tank is 1 m2, determine the force necessary to cause the tank to rupture.
The table below shows some published values of the growth parameters of SiO2 on silicon. For the dry growth process, the parameter t is already evaluated. Table 4.1 Oxidation coefficients for silicon Dry Wet (640 torr) Temperature ("C) A (µm) B (um'/hr) T (hr) A (um) B (um'/hr) 0.370 0.235 0.165 0.0011 800 920 0.50 0.203 1.4 0.37 0.0049 0.0117 0.027 0.226 0.11 0.05 0.287 0.510 0.720 1000 0.076 1100 1200 0.090 0.040 0.045 0.027 a) At a temperature of 1100°C, what starting oxide thickness does this data for the dry oxide growth assume? b) Using the parameters in the above table, determine total thickness if a dry oxidation was carried out for 5 hours at 1100°C. "
Hot mix asphalt (HMA) is commonly used in the construction of roadways in the United States at a rateestimated to be 500,000,000 tons/year. A typical upper layer (there may be as many as 5 layers ofdifferent thicknesses and compositions) of a high-volume highway is composed of crushed stone (alsoknown as crushed aggregate) and asphalt binder and is approximately 1.25 inches thick. The stone,which has a specific gravity of about 2.7, is mixed with asphalt binder (SG = 1.03) to form the HMAwith a composition of approximately 95 wt% aggregate and 5% asphalt. What is the volume ft3 of asphalt binder and weight (tons) of HMA required for the top layer of a 15-mile segment of interstatehighway with 5 lanes, each of which has a width of 12 ft?
Viscometer is used to measure the viscosity of a series of dilute solutions of a polymer in toluene at 30°C. (1) Intrinsic viscosity is the most useful of the various viscosity designations because it can be related to molecular weight by the Mark-Houwink-Sakurada equation, [n] = KM. Calculate the viscosity average molecular weight for this polymer by using the data given in Table 2. Given that the Mark-Houwink constant, K is 12 x 10-5 dl/g and a = 0.71. 0.505 0.595 0.804 Concentration 0 (g/dL) Flow time (s) 67.94 0.402 107.70 121.05 Table 2 132.77 161.39 1.207 227.84
A sawn-lumber column of 5.0 × 7.5-in. cross section has an effective length of 8.5 ft. The grade of wood used has an adjusted allowable stress for compression parallel to the grain σ = 1180 psi and an adjusted modulus E = 440 × 103 psi. Using the allowable- stress method, determine the largest eccentric load P that can be applied when e = 0.7 in. (Round the final answer to two decimal places.) 5.0 in. 7.5 in. D The largest eccentric load P that can be applied is kips.
A1.
2. You are to design a rectangular primary clarifier for a domestic wastewater plant to settle 900 m³/day with an overflow rate of 25 m³/m²-day. The tank is to be 3.2 m deep and 4.0 m wide. How long should it be and what detention time would it have? Calculate the weir loading rate to see whether it is overloaded if only one end weir is used.