Calculate. For a line frequency of 60 Hz, what is the ripple voltage if theload current is 250 mA and the capacitor is 500 μF?110v24v C.T.00000RmC

Step 1:*Formula picked up from Sedra Smith 6th ed Sec 4.5.4

Answered: For a line frequency of 60 Hz, what is…

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter21: Resistive-capacitive Series Circuits

Section: Chapter Questions

Problem 6RQ: A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating...

See similar textbooks

Similar questions

Calculate the ripple factor in a half-wave combiner circuit and the value of the output frequency, if you know that the value of Voc = 5V and 10 = V(rms)out) and the input frequency is 90 Hz
What's 21 22 23
QUESTION 3 An inductor, a capacitor, and a resistor are connected in parallel with a function generator. The inductor draws 100mA RMS, the capacitor draws 150mA RMS, and the resistor draws 200mA RMS. Find the magnitude of the total current. O 450mA RMS O 544mA RMS O 352mA RMS O 206mA RMS
5/1 IN4001 120 V 60 Hz R 5 k2 100 uF 1) Explain how this circuit works 2) Draw the waveform at the output (Vrl) for a sinusoidal signal at the input 3) What is the effective voltage of peak voltage in the secondary? 4) What is the peak voltage on the load? 5) What is the average voltage of the output (on the load)? 6) Calculate ripple on load
What is the form factor of this waveform...
A step up chopper has input voltage 110 V and output voltage 150 V. The value of duty cycle is.
5. Let's change our square wave to be less square. We're only going to have it be at the high voltage for 25% of the cycle. Sketch what you would expect Vout to look like now: ha n 2.T V S T 3T t
The rms value of the resultant current in a wire which carries a dc current of 20 A and a sinusoidal alternating current of peak value 20 A is 1. 34.1 A 2. 17.3 A 3. 24.5 A 4. 40.0 A
2. Sketch Vout if Vin is a 30 V peak to peak sinusoidal wave, D1 is germanium and D2 is silicon. Show your solution 1 K D1 D2 vin V OUT 3.3V 4.BV
Draw the waveform of voltage and current under the following conditions: A current which lags the voltage by 60°. A current which leads the voltage by 60°. A current which is in phase with the voltage
For the cycle circuit, when will the PIV appear when the input waveform will occur? Please choose one: a. B b. One c. C D
Determine the maximum peak-to-peak ripple current of previous problem by using the next equations, and compare the results. DI. = max V R tanh R 4fL DI = V S max 4fL

SEE MORE QUESTIONS

Recommended textbooks for you

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

For a line frequency of 60 Hz, what is the ripple voltage if the load current is 250 mA and the capacitor is 500 μF? 110v 24v C.T. 00000 R m C