For a fully developed laminar flow of water (dynamic viscosity 0.001 Pa-s) through a pipe of radius 5 cm. the axial pressure gradient is - 10 Pa/m. The magnitude of axial velocity (in m/s) at a radial location of 0.2 cm is decimal places). (up to two

Q: The ca jas z- 10GP3, has othe fos ortatA ASC EN

A:

Q: Complete the table below. LINE BEARING DIST (M) AB N 60° 15.3' E 40.311 BC S 64° 5.6' E 38.910 CD S…

A: Given: Line Bearing Distance, m AB N60o15.3'E 40.311 BC S64o5.6'E 38.910 CD S42o29.2'W…

Q: Explain the term Cunningham correction factor.

A: Cunningham Correction Factor (C): In dynamics of fluid, the Cunningham slip correction factor is…

Q: Define dilatometer test.

A: Dilatometer test is an in situ test method used to assess the strength and deformation of…

Q: Define undrained condition

A: If water is not allowed to flow in or out of the soil,  the stress path is called an undrained…

Q: I need information about waterproof work

A: Waterproofing work mainly used in construction works like building work for all the structural…

Q: Determine Qmax [Qmax = 6.48 x 10-4 m

A: To find Qmax

Q: 5. According to Fig. (a), (b), (c), specify what principle or relevant requirement is used on…

A: Dynamic tolerance diagram: Dynamic tolerance diagram 2 equal planes portray the volume of room used…

Q: 32 3" fo=3000 ps fy= NWC = Mn=?, Tied bars. 28 = 60 ksi 多#9 14

A:

Q: Define The width of the loaded area

A: Load: It is defined as the weight or force which is applied on the member, joint, or anybody which…

Q: What is Dimension D? Setback = 0.252, Bend Allowance = 0.345

A: The given values are as follows,The set back =0.252The Bend allowance=0.345To determine The…

Q: STA BS HI FS IFS ELEV BMa 1.265 225.70 0+00 3.5 +15 2.8 TP1 3.478 0.95 0+20 2.1 +25 3.2 3.6 +30 +35…

A:

Q: What is Uniformly loaded rectangular area at the surface ?

A: The external load coming from soil, water pores form the extra incremental stress.

Q: Given Velocity= 50m/s discharge= 5 m/s O = 180° vehicle %3D VI neglect frictioons Find the frce…

A: Given Data: Velocity is v=50 m/s. Discharge is Q=5 m3/s. Angle θ=180°

Q: Name the two primary types of float?

A:

Q: why the head loss is not YL= f*L/D* V^2/2g ?

A: Question :why the head loss is not YL= f*L/D* V^2/2g ?

Q: What is over-consolidated?

A: There are 3 types of consolidation stages namely : 1- over consolidation stage 2- normal…

Q: Define The shape of the loaded area

A: The shape of loaded area describes the intensity of loading at different sections and it's variation…

Q: Complete the table below. LINE BEARING DIST (M) LAT (m) DEP (m) DPD DA AB N 58° 46.9' E 38.588 BC S…

A: Given, Line Bearing Distance (l) (m) AB N 58°46.9'E 38.588 BC S57°59.7'E 37.736 CD…

Q: Explain - Explain why groundwater is more difficult to clean than surface water.

A: Groundwater and surface water are two primary sources of fresh water on our planet. However, they…

Q: diagram. 10kN.m 2m 3m (20+#ID)/2 KN 2m 5m 77 5kN/m B

A:

Q: 13. _________ is the process to determine the overall cost of project’s construction. Fill in the…

A: Processes of cost estimation are Empirical cost inference. Unit cost of bill of quantities. Types…

Q: Using the the following values, please calculate Specific Gravity Corrected G corrected (rounded to…

A: Given, K-value = 1.0004122 Uncorrected G = 2.251

Q: Describe the TRD method.

A: TRD stands for Trench Re-mixing and Deep wall. It is a one-phase process for excavation and in situ…

Q: Define the term Well Points.

A: A wellpoint is a well of small diameter used for dewatering.

Q: What is consolidation? Explain the concept of NCR and OCR with examples

A: Consolidation and the concept of NCR and OCR are explained in the next step.

Q: How MANY UNKNOWNS RESTROWTS MF thErE

A:

Q: Define Boussinesq’s Method

A: The Stress Computation Method determines how the 3-dimensional stress distribution due to loading is…

Q: 4 L Derive Elymax. (

A: This question is related to the Strength of the material from Civil Engineering.  In this question ,…

Q: What is the PreProposal meeting?

A: Pre-proposal meetins:

Q: Explain about the Drainage after Construction.

A: Drainage consists of the mechanical absorption of both surface and sub-surface mud. Drainage is also…

Q: Construction cost of the manufacturing plant is considered as overhead cost. True False

A: Explanation :  The construction cost of the manufacturing plant includes direct and indirect costs…

Q: what is possible grade of service value ?  a.  -1 b.  3  c. 0.1  d. 1.1

A: Brief concept- Grade of Service (GOS) - It is the category of service and comfort that is provided…

Q: Calculate the total area required for placing the quarry tiles on the internal walls in this…

A: There are two short walls and two long walls, And there is a deduction in area in the place of the…