A truck, with four wheel configuration and has loads as shown, will cross to a 12 m span bridge. A bridge engineer need to design a bridge section to accommodate these types of trucks and make some cases in selecting a cross-section beam 30 kN 20 kN 40 kN 50 kN 2 m 4 m 1m A B 12 m-

Q: own in millimeters. Note: DRAW OR ILLUSTRATE THE SUB-AREAS AND INDICATE THE CENTROID OF EACH…

A: To find the centroid-

Q: LQ.5: Calculate the force in member GC "Fgc = 24 kN " Tension O %3D %3D "Fgc 27 kN "Tension O %3D…

A: Given that:

Q: Don't waste my question. No wrong answer. House storage 95 ft x 65 ft must be finished with the drop…

A:

Q: Concrete Hollow Block 200mm H x 400mm Lx 150mm thick per piece and Laying 4 layers x 4 meters…

A: "Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: What are the parameters affecting the design of column baseplates?

A: introduction: column base plate: We design base plate for giving base to the column which give…

Q: 2 ft I ft 2 ft 1 ft 3 t

A:

Q: Define Total Stress Method.

A: The total vertical stress method is defined as method which is used for determining the stress…

Q: What area of steel is provided (per ft width) for No 6 @ 9"o.c.? O 0.66 in² O 0.88 in² O 0.59 in² O…

A: In the given question rebar number is given as 6 and 9" bar spacing  Use the table and find area in…

Q: (1) 3#8 4#10 15" I2.5" 24:5" Grade 60 steel. fé= 4000 psi, NWC. & Mn = ?

A:

Q: How to conduct a rebar tensile strength test?

A: Introduction : A sample is typically tugged to its breaking point in a simple tensile test to…

Q: Find the centroid of given composite figure. Set- up the reference axis on the lower left corner.…

A: Centroid about x-coordinate :x¯=A1x1+A2x2+A3x3A1+A2+A3

Q: (4) 5 &#8 187 #3" fé= 4000 pai Grade 60 steel NWC. Mn=?

A:

Q: What's the advantage of Composite structures?

A:

Q: GIVE 10 DISADVANTAGES OF USING HOLLOW BLCOKS

A: Disadvantages of using hollow blocks are : High Maintenance cost Load bearing capacity of the wall…

Q: How to Design Sealant Joint.

A: Sealants joints are the most underrated joints but they are the important joints when it comes to…

Q: Describe the auger method.

A: Auger method:

Q: How did you determine its a smooth pipe?

A: Given data: εd=9.87×10-5Nd=944,444.44

Q: how the compressive strength of the PET(Polyethylene Tetraphthalate ) filled  with soil and used as…

A: Compressive strength is the ability of material or structure to carry the loads on its surface…

Q: Mohr's circle is shown for a point in a physical object that is subjected to plane stress. Each grid…

A:

Q: Situation 21: A square tied column carries a factored load of 2800KN. It will be designed using…

A: Columns are structural members which carry compression loads transferred from the beams and slabs.…

Q: What is the recommended minimum diameter (mm) for temperature bars in one way slab? Express your…

A:

Q: Sealing Joint seals In the Exterior Walls and whats its uses.

A: Joint sealers area unit accustomed shut open joints to stay water associated air out (both exterior…

Q: the load is 150kN at the center of the beam and the dimension of the beam is 6x6x24. compute for…

A: P=150kN L=24 b=6 h=6

Q: What is the definition of a chill plate?

A:

Q: 1. Show how actual strength compared with design strength by plotting the published column strength…

A: Solution: Column curve: Column or strut is a compression member, the effective length of which…

Q: Prepare a complete NC program for finishing profile shown in fig.2 with continuous cut in clockwise…

A:

Q: Define the following i) SMRF Structures ii) IMRF Structures

A: 1. The SMRF structures and IMRF structures are types of moment-resisting frames use to resist the…

Q: un in the figure. Locate its intersection with and y axes. 390 N 13 30 12 %3D 722 N

A:

Q: List the points that are pertinent in the care of tapes.

A: In surveying most of the measurements is done with the help of tape, following are some pertinent in…

Q: Describe Applying the shotcrete wall surface.

A:

Q: Why is space filled with grout in this image necessary? Column Bar Plate Top Nut Grout Bottom Nut…

A: We know that grouting is generally used to fill the voids or  space between the two surfaces so that…

Q: Write any differences between plain and reinforced concrete column

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: Discuss Allowable Stress Design

A: MAIN CONCEPT OF DESIGN: load<resistance ALLOWABLE STRESS DESIGN is one of the design concept. In…

Q: Identify Zero force member? Bo A E H Answers are: -->BC, EG, EF & DF

A:

Q: Describe about the Flat-blade dilatometer testing.

A: The Flat Dilatometer Test:

Q: Find the most economical proportions for cylindrical cup. Show detailed solution

A: We know, Volume of a cylinder, V = 14πd2h           where d = diameter of cylinder and h = height of…

Q: Problem 1: Calculate Mn and check the minimum steel limit f'c =4 ksi, fy = 60 ksi. 2.5" 25" 6-#9…

A: Given doubly reinforced beam with values,Width of the beam, b= 12''Effective depth,…

Q: Define Temperature gradient loads

A: Temperature gradient loading occurs in the structural elements like the beam element and the plate…

Q: Find the moment of inertia (Ix, mm“) of the composite shape from the bottom base. Type answer in two…

A:

Q: Q: report about metal sleeper

A: Sleepers are provided in rails to transfer loads from rails to ballast. It acts like a fixture…

Management of Materials

Materials form the basic ingredient or the raw supplies before the final product. Materials cover the inventory storage in typical warehousing. All manufacturing processes and production processes require different materials.