For a frame shown, a 4442 N load is acting on a member ABD at D. If the allowable material shear stress for is 44 MPa, determine the required diameter (rounded off to the nearest 2.5mm) of the pins at C and D. Pin C and pin D are subjected to double shear and single shear, respectively. If the thickness of member BC is 12mm and that of member DE is 16 mm, determine the maximum bearing stress at C.

For a frame shown, a 4442 N load is acting on a member ABD at D. If the allowable material shear stress for is 44 MPa, determine the required diameter (rounded off to the nearest 2.5mm) of the pins at C and D. Pin C and pin D are subjected to double shear and single shear, respectively. If the thickness of member BC is 12mm and that of member DE is 16 mm, determine the maximum bearing stress at C.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.8.1P: Compute the nominal shear strength of an M107.5 of A572 Grad 65 steel.

See similar textbooks

Related questions

Q: A 20-mm-thick plate is bolted to the flange of a T-beam to form a -200 mm 20 mm built-up beam. If…

A: Calculate the moment of inertia of I section…

Q: 2. The structure is used to support a distributed load of w = 5 kN/m. The bolts at A, B, and C each…

Q: 6. In the steel structure shown, a 6mm diameter pin is used at C and 10mm diameter pins are used at…

Q: The truss shown consists of wooden members. Knowing that each member has a 50 x 50 mm. square…

Q: Determine the maximum permissible value of T provided the allowable shearing stresses in brass and…

A: ζb=70 MPaζs=110 MPaGb=80 GPaGs=40 GPa di=70 mmd0=90 mm

Q: In the steel structure shown a 6 mm diameter pin is used at C and 10 mm diameter pin is used at B.…

A: Given:Diameter of pin at C is 6mmDiameter of pin at B is 10 mmRequired:Largest P applied

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal…

A: Given :

Q: For the shaft loaded as shown, which point(s) at the section shown experiences the maximum shear…

A: Let's draw the FBD for first figure At the L shaft observe the stresses and their directions…

Q: Two 10-mm thick plate members are to be connected using straps of the same thickness and 12-mm…

Q: the loading shown, determine (a) the stress at points A and B, the point where the neutral axis…

A: A=4*1.8=7.2 in3 Iz=(4*1.83)/12=1.944 in4 Iy=(1.8*43)/12=9.6 in4

Q: Two 10-mm thick plate members are to be connected using straps of the same thickness and 12-mm…

A: Given Data: Thickness of plates is t=10 mm. Diameter of rivet is d=12 mm. Maximum tensile stress on…

Q: Q1. The structure shown consists of a S18 x 70 rolled-steel beam AB and two short members welded…

A: Finding out SFD and BMD of beam and maximum normal stress.

Q: A joint connection is shown below. If the average shear stress in the pin must not exceed 107 MPa,…

A: Given: Max. shear stress = 107MPa, D=12mm = 12*10-3 Ma. applied load, P= ?

Q: ABD rigid bar with 40mm diameter BC bar at point B, It is supported from point A with a 30 mm…

Q: Three round bars welded together are axially loaded as shown. Find the normal stress in each bar if…

Q: 1.51 In the steel structure shown, a 6-mm-diameter pin is used at C and 10-mm-diameter pins are used…

Q: Two vertical forces are applied to a beam of the cross section shown in Fig.2. Determine the maximum…

Q: FOR THE LAP JOINT SHOWN, DETERMINE THE MAXIMUM SAFE LOAD 'P' WHICH MAY BE APPLIED IF THE SHEARING…

Q: Determine maximum load (P1) that can be applied without exceeding design tensile stress in plates

A: Solution: allowable tensile stress F1 = 0.6 Fy = 0.6 x 248 = 149 Mpa P = FtAn An =…

Q: Two wooden members of uniform rectangular 150 mm cross-section are joined by a simple glued scarf…

A: Area = 75 mm x 150 mm = 0.150 m x 0.075 m Allowable shear stress = 620 kPa = 620 x 103 N/m2

Q: The

Q: 3. For the given structure and boundary conditions, what is the allowable load Pallow if the…

Q: Two plates with a thickness of 35mm, width of 160mm, and length of 200mm are joined ogether by a pin…

A: thickness =35mm Width =160mm Length =200mm Pin Diameter =60mm

Q: Two 10-mm thick plate members are to be connected using straps of the same thickness and 12-mm…

A: From the arrangement, we can observe that the maximum tensile strength occurs in the line of rivets.

Q: Assume that 4-18mm diameter rivets join the plates that are each 120mm wide. The allowable stresses…

Q: . For the riveted connection shown in the figure using elastic analysis a. Determine the safe value…

A: Diameter of rivet = 25 mmAllowable shear stress = 150 MPaloading = 50 KNOther Data are given in the…

Q: Problem 01.054- Analysis of an inverted T-frame In the steel structure shown, a 6-mm-diameter pin is…

Q: A gusset plate is connected to the flange of column with the help of fillet weld on both sides as…

Q: The strain at point A on the bracket has components = 330 (10-), ey = 560 (10-). Yxy = -570 (10-0).e…

A: Data given εx = 330×10-6 εy = 560×10-6 εz = 0 γxy = 570×10-6 To find:- Maximum shear strain…

Q: A stepped shaft has the appearance shown in Fig 5-13. The region AB is aluminum, having G 28 GPa,…

A: We have to calculated max. shear stress in steel and max. shear stress in aluminum in end A and C .

Q: a. If the control rod AB is made of a steel having an ultimate normal stress of 600MPA, determine…

Q: 2. Member AB shown in the figure supports a 5 N/m uniformly distributed load and 4kN concentrat load…

Q: 1.42 Link AB is to be made of a steel for which the ultimate normal stress is 65 ksi. Determine the…

Question

E
00
1.00 m
1.54m
O
B
Ao
www
4442 N
45⁰
1.54 m
1.52 m
For a frame shown, a 4442 N load is acting on a
member ABD at D. If the allowable material shear
stress for is 44 MPa, determine the required diameter
(rounded off to the nearest 2.5mm) of the pins at C
and D. Pin C and pin D are subjected to double shear
and single shear, respectively. If the thickness of
member BC is 12mm and that of member DE is 16
mm, determine the maximum bearing stress at C.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Follow-up Questions

Read through expert solutions to related follow-up questions below.

Follow-up Question

determine the maximum bearing stress at C

Solution

by Bartleby Expert

SEE SOLUTION

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Given the following allowable stresses:• 50 MPa for shear in rivets• 100 MPa for bearing between a plate and a rivet• 80 MPa for tension in the platesDetermine the maximum load P that can be applied to the lap joint connected bythree – 16 mm diameter rivets. Note: Draw its FBD
Problem 4 Determine the design tensile strength Pn of the MC18x58 channel shown based on yielding and rupture of the tension member. Do not check block shear. 1. Gusset PL. 7/8"] 5@3" MC18x58 1 1/4 in Standard Holes**
Determine the a) normal stress in rod (1), b) the shear stress in pin B and the shear stress in pin A given the following properties of the structure. The tie rod at 1 is 10 mm in diameter. Pin Pin Connection Diameter SET e a b h Connection Type at B & D of pins Type at A A 1300 N 45° 600 250 450 Double Single Shear 12 mm mm mm mm shear D (1) C b
6. Member BC in the truss below is a 300 mm wide, 10 mm thick steel plate attached to two other 12 mm plates at Joint C by three 24mmp A490N bolts. The plate is A36. Determine the safe load Pu using LRFD that the truss can resist according to the capacity of the connection. 15 15 с 1.5 3P. + D 1.5 80 mm 70 mm 70 mm 80 mm Fac 7. Repeat Problem 6 using 30mm A325-N bolts and A-50 steel. Use ASD. 50 mm Fac
Test#1 -zzen-zax AlpQLSdM75VMOVqbMa1WtS9n99RYc6PifeGUTpVBOluyMUUVYQgqqA/formResponse YouTube Replace the three forces which act on the bent bar by a force-couple system at *.the support point A 2100 lb 4' 1500 lb •A B. 30° C. 2' •E. 800 lb 3' oogle
43 OSFu A tension member with an allowable tensile stress of 0.6Fy is connected to the gusset plate using four rivets having a diameter of 34mm. Assume the diameter of the hole is 2mm more than the rivet diameter. It is required to determine the value of b so that the net width along rivets 1-2-3-4 is equal to the net width along 1-2-4. > Determine the value of b > Determine the most critical net area The value of T without exceeding the allowable stress. Gusset plate If failure will occur in djagonal s 2 direction add a value 4g C0mm b. 6. 100mm 400mm 100mm 100mm 12mm 150mm
The following image shows a front and side view of the column connection. The bolts have a diameter of ¾”. The W12X65 profile has a thickness of 0.605”. Determine: a. The shear stress in the bolts. Answ. 11.81 ksi b. The axial stress in the bolts. Answ. 23.62 ksi c. The support stress in the W12X65 profile. 11.50 ksi
Determine the development length of the #9 bars. Is it safe? Determine the shear capacity of a W21x44.
16
Theory of structure Influnce Lines
REVISED PROBLEM: M3 HW 4 4. Six rivets are used in the connection shown in the figure. If both P = 50 kN, what is the minimum diameter P- 50 rivet is necessary so as not to exceed the 70MPA allow shearing stress? What thickness of plate is required so as not to exceed a bearing stress of 140 MPa? 80 mm 80 mm Peso 100 m
2. Member BC in the truss below is a 300 mm wide, 10 mm thick steel plate attached to two other 12 mm plates at Joint C by three 24 mm diameter A325N bolts. The plate is A50. Determine the safe load Pu using ASD that the truss can resist according to the capacity of the connection. LS 15 WR + 14 DATE ON ON Mmm 70 m 40 mm