Following are the results from the liquid and plastic limit tests for a soil. Liquid limit test: let the N1 be 20 and w1 be 30% let N2 be 30 and w2 be 20% let N3 be 40 and w3 be 10% For Plastic limit test: let w1 be 12 and let w2 be 13 and let w3 be 13.5 The liquid limit = Plastic limit = Plasticity Index =

Following are the results from the liquid and plastic limit tests for a soil. Liquid limit test: let the N1 be 20 and w1 be 30% let N2 be 30 and w2 be 20% let N3 be 40 and w3 be 10% For Plastic limit test: let w1 be 12 and let w2 be 13 and let w3 be 13.5 The liquid limit = Plastic limit = Plasticity Index =

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Laboratory test results for a sample of clay soil for the purpose of evaluating the potential for volume change (swelling, expansion) are shown Liquid limit = 60% %3D Plastic limit = 24% %3D Particles smaller than 0.002 mm = 44% %3D Compute the plasticity index O 44 68 O 24 O -44
U B. ( A Soil Specimen has the following characteristics: % passing No.4 sieve = 85 % passing No.200 sieve = 11 D60 = 2 mm D30 = 0.35 mm D₁0 = 70 μm L.L = 36% P.L = 31% D8 = 2 µm 1. Classify the specimen according to the Unified Soil Classification System (USCS). Assign the group name and the group symbol. 2. Determine the soil activity. 3. Determine the soil Liquidity index and consistency index if we = 26%.
A liquid limit test on a clay was performed with the following results. The natural water content of the clay is 38% and plastic limit is 21%. Number of Blows 6 12 20 28 32 Water content (%) 52.5 47.1 42.3 38.6 37.5 What is the liquid limit of this clay? (Use Interpolation) Group of answer choices 39.85% 39.99% 36.74% 38.63% Please answer this asap for upvote. Thanks
The data shown below are the results of a liquid limit test done on a soil. Moisture Content (%) Cone Penetration (mm) 26 12 30 16 33 22 37 28 42 30 What is the consistency index of the soil if plastic limit is 10 and water content is 28%?
4. The results of liquid limit testing on 3 samples of a soil are shown below. sample 1. 2 3 mass (g) 20 mass mass (g) emply can (M.) wet soil + can (M.) dry soil + can (M) moisture content: w (%) Number of cranks 20 20 35 35 28.82 36 28.15 30.38 4 10 30 Calculate the moisture content of cach of the 3 samples. Show your calculations below and then put your answers in the chart above. M,- M, м, - м, x100%
5. The following information is obtained from a sieve analysis to determine the range of particle sizes in a granular soil sample. Sieve Size Sieve Opening (4.76) Percent Finer#4 4.76 96#10 2.00 80#20 0.84 51#40 0.42 38#60 0.25 25#100 0.149 12#200 0.074 5 Present the information as grain-size curve on semi-logarithmic coordinates of percent finer against particle size diameter. From the plot, determine the uniformity coefficient Cu.
1.4 A test for the relative density of soil in place was performed by digging a small hole in the soil. The volume of the hole was 400 ml and the moist weight of the excavated soil was 9 N. after oven drying, the weight was 7.8 N. Of the dried soil, 4N was poured into a vessel in a very loose state, and its volume was found to be 270 ml. The same weight of soil when vibrated and compacted had a volume of 200 ml. Determine the relative density.
05: The Figure below represents the data that was obtained from a liquid-limit test on a soil. 50 percent of its particles is passing sieve #200. Two determinations for the plastic limit gave water contents of 20.3 % and 20.8 %. Determine 1- Liquid Limit (LL). 2- Plasticity index. 3- Liquidity index if the water content is 27.4% 4- Void ratio at the liquid limit, if G, 2.7 5- Classify the soil based on AASHTO system. 30 10 20 40 60 80 100 Penetration, d (mm) Moisture content, w ()
Sr B. ( A Soil Specimen has the following characteristics: % passing No.4 sieve = 85 % passing No.200 sieve = 11 D60 = 2 mm D30=0.35 mm D₁0 = 70 μm D8=2 μm L.L = 36% P.L = 31% 1. Classify the specimen according to the Unified Soil Classification System (USCS). Assign the group name and the group symbol. 2. Determine the soil activity. 3. Determine the soil Liquidity index and consistency index if wc = 26%.
Discuss your results and compare your results with any published data. For the bulk density test, obtain the value of dry density. How does the values of (i) void ratio (ii) porosity influenced your results? How will these values differ if the soil is fully saturated, partially saturated or submerged? Support your assertions using relevant phase relationship equations. Whatwill happen to the values of particle density (specific gravity) obtained if the soil sample contain large quantities of peat or organic material? How will the results be used in specific practical conditions in the construction industry? Explain any source(s) of error in your experiment and state how it affected your result.
A liquid limit test on a clay was performed with the following results. The natural water content of the clay is 38% and plastic limit is 21%. Number of Blows 6 12 20 28 32 Water content (%) 52.5 47.1 42.3 38.6 37.5 What is the plasticity index of this clay? (Use Interpolation) Group of answer choices 15.74% 18.99% 18.85% 17.63% Please answer this asap for upvote. thanks
Q # 1. Organic soils are typically characterized by high void ratio, low specific gravity, and high compressibility. Following are the results of a consolidation test on a sample of organic soil. Pressure, o (kN/m2) Change in dial reading, AH (mm) 0.284 12 0.150 24 0.315 48 0.564 100 0.823 200 2.25 400 5.34 Given that the initial height of the specimen = 20.6 mm, mass of dry specimen = 12 g, area of specimen = 31.67 cm2 and G, = 2.49. Plot the e, log o' curve. b. Determine the preconsolidation pressure. a.